ABS filaments

Sunlu S4 Filament DryerThe SUNLU FilaDryer S4 is an advanced filament dryer designed for demanding 3D printing users. It offers a massive capacity—drying up to 4 spools (1 kg each) simultaneously—and the ability to work with multiple printers at once. With a power output of 320–330 W, rapid heating (up to 50°C in just 30 minutes), and a maximum temperature of 70°C, the device ensures effective and uniform drying of even the most demanding materials, such as PA or PC. The built-in humidity control system, touchscreen, 8 filament outputs, and predefined material profiles make using the device not only effective but also extremely convenient.Dry up to 4 filaments simultaneously – maximum productivityThanks to the large chamber (450 × 210 × 211 mm), you can dry up to four spools of filament at the same time. This is the perfect solution for multicolor printing or working with multiple printers simultaneously. You don’t waste time changing materials—everything is ready in one place, which significantly speeds up and streamlines the entire process.Instant heating and high power – efficiency that makes a differencePerformance is ensured by a PTC heater with a power of up to 330 W, which allows it to reach 50°C in about 30 minutes and a maximum of 70°C. This means shorter filament preparation time and greater drying efficiency. Even difficult, hygroscopic materials regain their properties faster than ever before.Ideal temperature balance – perfect drying for every spoolA three-fan system (on the sides and bottom) ensures even air circulation and temperature stability within ±3°C. This ensures that every section of the filament is dried evenly, resulting in better print quality, greater consistency, and no surprises during operation.Smart humidity control – filament always in perfect conditionAn advanced humidity control system automatically starts drying when the humidity level exceeds the set range (30–50%) and stops the process once optimal conditions are reached (approx. 25%). This means full automation and the assurance that the filament is always ready for use—without manual monitoring.Safety and ease of use – technology you can rely onThe SUNLU S4 is equipped with a triple safety system: a PTC heater, a temperature sensor, and software protection. The device monitors temperature in real time and alerts you to any abnormalities, ensuring safe operation. Additionally, the touchscreen and pre-set profiles for PLA, ABS, PETG, TPU, PA, and PC simplify operation and eliminate the guesswork involved in settings.Full compatibility and flexibility – tailor the equipment to your needsSupport for filaments with diameters of 1.75 mm, 2.85 mm, and 3.00 mm, along with compatibility with most 3D printers, ensures the SUNLU S4 performs well in any environment. Eight filament outputs and the ability to connect multiple printers simultaneously allow for flexible workstation configuration. This device truly expands your capabilities and lets you create without limits.Included: SUNLU S4 Filament Dryer Power cord PTFE tubes User manual Manufacturer Sunlu Model Fila Dryer S4 Rated power 320–330 W Power supply AC 100–240 V / 50–60 Hz Maximum temperature 70°C Heating time to 50°C approx. 30 minutes Capacity 4 spools (1 kg each) Internal dimensions 450 × 210 × 211 mm Device dimensions 516 × 278 × 350 mm Net weight 4.8 kg Gross weight 5.5 kg Heating system PTC + 3 fans Temperature stability ±3°C Humidity control Automatic (start 30–50%, stop approx. 25%) Supported materials PLA, ABS, PETG, TPU, PA, PC Supported filament diameters 1.75 mm / 2.85 mm / 3.00 mm Number of filament outlets 8 (can be used with PTFE tubes) Display Touchscreen LCD

CREALITY SpacePi X4L Filament Dryer3D printing requires properly prepared filament. Even a small amount of moisture can compromise print quality, cause air bubbles, or result in poor layer adhesion. The Creality SpacePi X4L Filament Dryer is designed to keep the material in optimal conditions before and during printing. The device uses smart sensors, temperature control, and an intuitive touchscreen panel, making filament drying simple and precise.Smart Temperature and Humidity SensorsThe SpacePi X4L uses advanced sensors to monitor temperature and humidity inside the chamber. This allows the device to respond to even slight changes in parameters and maintain stable drying conditions. In practice, this means more uniform filament preparation, which translates to a more stable material flow during printing and better model quality.LCD touchscreen with operation controlThe device is operated via a clear LCD touchscreen. The new display design with an anti-static coating ensures good visibility even in cooler conditions. The panel allows you to quickly set the drying time and temperature, and the automatic mode selects the appropriate parameters on its own. You can also check the humidity level inside the device in real time on the screen.Double insulation for safetyThe dryer’s housing is equipped with a double layer of insulation that retains heat inside the chamber. The drying temperature can reach up to 75°C, yet the outer part of the housing remains significantly cooler—around 60°C. This allows the device to be safely operated even while in use.Wide filament compatibilityThe Creality SpacePi X4L supports most popular filaments used in 3D printing. The device is compatible with 1 kg or 2 kg spools and filaments with diameters of 1.75 mm and 2.85 mm. The chamber accommodates spools with a diameter of up to 200 mm and a width of up to 150 mm, making it compatible with many materials used in 3D printers.Precise time and temperature controlThe dryer allows you to set the temperature between 45 and 75°C and the operating time from 1 to 48 hours. This allows you to tailor the drying process to specific materials, such as PLA, PETG, TPU, or other filaments that require moisture removal before printing. Manufacturer Creality Model SpacePi X4L Product dimensions 382 × 290 × 270 mm Weight 5 kg Housing material ABS / PA / PC Operating temperature range 45–75°C Drying time 1 to 48 hours Rated power 340 W Input voltage 220–240 V ~ 50/60 Hz (UK / EU / AU / BR / CL / AR), 100–120 V ~ 50/60 Hz (US / JP) Filament diameter 1.75 mm / 2.85 mm Maximum spool diameter 200 mm Maximum spool width 150 mm

ELEGOO Neptune 4 Pro 3D PrinterThe ELEGOO Neptune 4 Pro is a state-of-the-art FDM (Fused Deposition Modeling) 3D printer that combines high speed, precision and robust design. Based on the Klipper motherboard, it offers a large working area of 225 × 225 × 265 mm and printing temperatures of up to 300°C, and allows you to use a wide range of filaments - from PLA (Polylactic Acid, poly lactic acid) and PETG (Polyethylene Terephthalate Glycol, modified Polyethylene Terephthalate Glycol) to ABS (Acrylonitrile Butadiene Styrene, an acrylonitrile-butadiene-styrene copolymer), TPU (Thermoplastic Polyurethane) or nylon. With a powerful extruder and automatic 121-point leveling, the Neptune 4 Pro can handle both rapid prototyping and long, demanding technical prints.Fast printing without compromiseThe printer reaches a maximum speed of 500 mm/s, with a recommended 250 mm/s guaranteeing excellent quality with short turnaround times. Backed by the Klipper motherboard, a powerful ARM (Advanced RISC Machine, an advanced RISC architecture) 64-bit 1.5G quad-core processor and features such as Input Shaping and Pressure Advance - it provides an exceptionally smooth model surface and even filament stamping. It is an excellent choice for those who expect not only accuracy, but also real time savings.Efficient cooling system, thoughtful table designTwo double-sided 4015 fans and four 4020 fans ensure effective heat dissipation and cooling of printed models. What's more, the device's heating table is divided into two segments with different powers - 150 W and 100 W. This solution guarantees lower power consumption and protects against overheating, resulting in more stable and safer operation.Improved hotend and efficient extruderThe Neptune 4 Pro is equipped with a high-performance direct-type extruder with dual gears, which ensures precise and stable filament feeding, regardless of the type. In addition, the hotend with an improved design uses a copper-titanium thermal tube and a nozzle capable of operating at 300°C. This solution allows printing from a wide range of materials, including those requiring higher temperatures and better flow.Guidance stability and structural rigidityThe printer is equipped with metal X- and Y-axis guides, which, combined with dual U-shaped ball bearings, ensure smooth, precise and stable guidance of the print head. In addition, a reinforced, widened Y-axis profile increases the rigidity of the entire structure, resulting in higher print quality, especially at high speeds.Automatic leveling and flexible platformThe printer uses automatic table leveling at as many as 121 points (11×11 grid), which ensures perfect adhesion and a perfectly aligned first layer. In addition, the user can use the knobs underneath the work platform to manually adjust the level - for even greater accuracy and full control over the printing process.Intuitive operation and flexible communicationA detachable 4.3" touchscreen allows you to conveniently preview your model and stop printing. In addition, the printer allows you to transfer files via USB (Universal Serial Bus, a universal connector for data and power) or LAN (Local Area Network, a local computer network).Additional capabilitiesWith a filament sensor and a resume function after an interruption, you can be sure that printing will not fail, even if something unexpected happens. LED (Light Emitting Diode) lighting at the nozzle makes it easy to see details up close, and an additional LED strip provides even illumination throughout the work area.More space for your ideasThe Neptune 4 PRO offers a workspace of 225 × 225 × 265 mm, allowing you to create both small prototypes and more elaborate models. This volume gives you a lot of design freedom without having to split models into parts. Manufacturer ELEGOO Model M6-512 Maximum printing speed 500 mm/s X, Y axis All-metal axis guides with double U-shaped ball bearings Pressure Advance function Yes Input Shaping function Yes Heating table

Creality Ender-3 V3 3D PrinterCreality Ender-3 V3 is an advanced 3D printer that combines cutting-edge technology, stable design and intuitive interface to offer professionals and enthusiasts a tool for creating precise prints. With FDM (fused deposition modeling) technology, the printer provides high-quality prints in a variety of materials.Powerful printing functionsThe printer allows modeling in a variety of materials, such as PLA, TPU, PETG, ABS, PLA-CF, PETG-CF and CR-carbon, offering a wide range of design possibilities. It offers filament detection functions, which prevents interruption of the printing process. It takes place at speeds of up to 600 mm/s, and the coordinated movement of the X- and Z-axis is driven by two motors attached to the base, which increases the accuracy of the Z-axis and enables better quality prints. The printer supports the Gcode file format and allows printing from a USB drive, via LAN or from the cloud.Advanced designThe Ender-3 V3 features a new metal construction with die-cast parts for greater stability and durability. The gantry and base are made from a single piece of metal, further improving the accuracy of the Z-axis for better quality prints. The printer is also equipped with full-power direct extrusion, enabling clog-free extrusion for more than 1,000 hours. A 60-watt ceramic heater ensures full melting of filaments at high speed.Advanced coolingThe printer is equipped with a durable copper nozzle with a steel tip and titanium alloy heat shield. In addition, two powerful fans at the front and rear of the print head quickly and evenly cool the freshly printed section, ensuring excellent print quality even at high speeds.Easy operation and setupThe Ender-3 V3 offers automatic level detection and calibration, which prepares the printer for operation without the need for manual leveling. The printer is also equipped with a 4.3-inch HD color touchscreen that allows easy monitoring of the printing process, model previewing and temperature control with moving graphics. In addition, the printer features a Windows and Mac OS-compatible operating system, providing versatility in operation.Performance and precisionThe printer offers a maximum print speed of 600 mm/s and a maximum acceleration of 20000 mm/s^2, enabling fast and precise prints. The direct-driven extruder is reinforced with a helical spring and ball piston, ensuring strong filament gripping without slowing down. Extruder enhancements such as a side spring, ball piston and powder metallurgy lever further increase adhesion and extrusion force for precise printing.State-of-the-art printing featuresThe printer has an excellent software ecosystem that allows control and monitoring with Creality Print slicer and Creality Cloud APP. This system allows easy management and export of models. The spring steel base allows the model to be released with a slight bend, which is useful in the printing process. Manufacturer Creality Model Ender-3 V3 Modeling technology FDM Modeling dimensions 220 x 220 x 250 mm Leveling method automatic level detection Number of nozzles 1 pc. Extruder diameter 0.4 mm Layer thickness 0.1-0.35 mm Precision ±0.2 mm Nozzle temperature ≤ 300 Substrate temperature ≤ 110 Filaments PLA / TPU / PETG / ABS / PLA-CF / PETG-CF / CR-carbon Rated power 350 W Input voltage 100-120 V; 200-240 V; 50/60 Hz Filament detection Yes Lost power recovery Tak Printing method From USB disk / via LAN / from the cloud Print file format Gcode Clipping software Creality Print Operating system Windows / Mac OS Language Chinese, English, Spanish, German, French, Russian, Portuguese, Italian, etc.

Anycubic Kobra 3 V2 3D printerMeet the Anycubic Kobra 3 V2, a 3D printer that offers precise and fast printing. Its enhanced LeviQ 3.0 automatic leveling system with a 60 mm Y-axis and SG15 bearings guarantees perfect adhesion and flawless first layers, while speeds of up to 600 mm/s² and acceleration of 20,000 mm/s² reduce turnaround time for even the most demanding projects. Thanks to "plug & play", installation and initial startup take less than 15 minutes, while smart features such as resuming printing after power loss, filament detection and timelapse on the built-in 720 p camera ensure continuous and safe operation. The whole thing is complemented by the powerful Anycubic ecosystem, which gives you full control over every printing step.LeviQ 3.0 automatic levelingForget about tedious manual table calibration. The innovative LeviQ 3.0 system with a 60 mm Y-axis and SG15 bearings on the X-axis takes care of the perfect alignment of each layer. Thanks to the elimination of offsets in the Z-axis, you will get reliable adhesion of the first layer, which significantly increases the success rate of prints even on the most geometrically complex projects.Express speed and reliable performanceYou no longer have to wait long to print your designs. The Kobra 3 V2 achieves a maximum print speed of up to 600 mm/sec (300 mm/sec by default) and acceleration of up to 20,000 mm/sec², resulting in a small boat model in less than 13 minutes. The improved nozzle effectively minimizes filament leakage, and the optimal width of the working tunnel ensures comfort when working on any project.Unpack and runAssembling and starting the printer takes less time than your morning coffee - the intuitive, simplified design allows you to start your first print in a quarter of an hour after unpacking. Sturdy twin pull bolts, a precision bearing system and a metal quick-release coupler guarantee the stability of the entire design and allow for instant nozzle changes when needed.Smart monitoring and securityAnycubic Kobra 3 V2 has a filament sensor that detects its condition and automatically refills it. In addition, the printer resumes operation after a power outage or unexpected power loss. The built-in 720p timelapse camera allows you to document the entire process, which is great for order presentations or creating social media content.Full control in the Anycubic ecosystemWith Anycubic Slicer Next (based on the Orca engine), you'll prepare models for printing from the LAN, managing multiple projects simultaneously and skipping unwanted elements. Using Anycubic, you gain remote access to the printer, real-time progress monitoring and a time-lapse photography option. In addition, the Makeronline platform offers a rich library of pre-made models and one-click cutting and printing.Comprehensive feature setAnycubic Kobra 3 V2 is more than a printer. It's a tool that integrates top-notch automation and intelligent software. With a capacitive 4.3-inch touchscreen and control via panel, app and USB, you have complete freedom to choose how and where to work on your projects.Included Kobra 3 V2 printer print head touchscreen spool holder cable holder cleaning wiper screw M2x14 x2 screw M3x6 x4 screw M4x16 x2 screw M3x10 screw M3x8 power cord cable organizer x2 USB disk filament tube set of wrenches allen screws 4.0, 3.0, 2.5, 2.0, 1.5 sample of filament nozzle cleaner grease camera instruction manual Manufacturer Anycubic Model K3V2-IP-O Weight 9.37 kg Supported materials Kobra 3 V2 supports only PLA, TPU, PETG, ABS materials Dimensions 452.9 x 504.7 x 483 mm Power source 400 W Multicolor printing For multicolor printing, the ACE Pro is required Nozzle Maximum temperature 300℃ Print size 255 x 255 x 260 mm Maximum table temperature 110℃ Maximum print speed 600 mm/sec Touch screen 4.3-inch Active drying ACE Pro required Auto leveling mode LeviQ3.0 + no Z-axis offset + design optimization Nozzle diameter Standard 0.4mm, options: 0.25/0.6/0.8mm Filament detection a

Anycubic ACE 2 Pro Multi-Filament System for the Kobra S1The Anycubic ACE 2 Pro is an advanced multi-filament system that opens up new possibilities in 3D printing, allowing you to create models in up to 16 colors. It supports 4 colors as standard, but connecting four units allows you to significantly expand the color palette and tackle more complex projects. The system is compatible with Anycubic printers such as the Kobra 3, Kobra 3 V2, Kobra 3 Max, Kobra S1, Kobra S1 Max, and Kobra X, offering great flexibility in adapting to your existing equipment.Smooth and fast filament feedingThe device uses 4 independent brushless motors that ensure stable, quiet, and precise operation. A new-generation buffering mechanism ensures smooth filament feeding and retraction, eliminating the risk of jams in each channel. Loading speed has been increased to 50 mm/s, a 100% improvement over the previous version, and filament change time has been reduced to approximately 56 seconds, saving up to 47 minutes over 100 changes.Optimal conditions thanks to drying and humidity controlThe ACE 2 Pro system allows for simultaneous filament drying and printing, keeping the material in optimal condition throughout the entire operation. Built-in temperature and humidity sensors monitor conditions in real time, and a solenoid valve actively removes excess moisture. An additional silicone ring seal protects the filament from external factors, resulting in better print quality and a lower risk of errors.Durable construction and quiet operationThe input ports, made of alumina ceramic, are highly wear-resistant, which extends the device’s lifespan and reduces the need for maintenance. Brushless motors offer a lifespan of at least 5,000 operating hours. At the same time, the device operates very quietly—below 48 dB with the door closed, and around 55 dB during active drying—allowing for comfortable use even in enclosed spaces.Easy maintenance and quick jam removalThe use of external feed channels and a quick-release mechanism allows for instant disassembly and removal of any jams. As a result, servicing takes only a few seconds and requires no complicated tools, significantly enhancing user convenience.Smart printing assistanceThe built-in smart assistant system offers features that genuinely simplify daily work. The device estimates the amount of filament remaining on the spool, automatically switches to a new spool when it runs out, and recognizes Anycubic filaments and their parameters (when connected to the internet). This makes the printing process more predictable and maintenance-free. Manufacturer Anycubic Model Ace 2 Pro Product code DS20-IP-O Dimensions 368 × 291.5 × 236.5 mm Weight 3.7 kg Enclosure material ABS/PC Motors 4 × brushless motors Filament compatibility PLA, PETG, ABS, ASA, PET, PA, PC, PVA (dry), BVOH (dry), PP, POM, HIPS, PLA-CF, PETG-CF, PAHT-CF, TPU (for ACE), PVB Filament diameter 1.75 mm Spool compatibility Spool outer diameter: 195–200 mmSpool width: 60–68 mmSpool thickness: 3–6 mm Smart filament identification Supported Filament end detection Supported Automatic print resume Supported Maximum drying temperature 65°C Drying efficiency Suitable for: PLA, PETG, PVB, TPUCompatible but not optimized: ASA, ABS, PET, PA, PC, PP, BVOH, POM, HIPS, fiber-reinforced materials Active humidity control Supported Sealed chamber Supported External PTFE tube Supported Temperature and humidity monitoring Temperature and humidity levels (visible in the app, slicer, and on the printer screen) Rated power 220 V: 330 W (max.)110 V: 235 W (max.) Printer compatibility Kobra 3 / Kobra 3 V2 / Kobra 3 Max / Kobra S1 / Kobra S1 Max / Kobra X

AnyCubic Kobra 3 Combo 3D Printer K3CBBK0A-O

ELEGOO Centauri Carbon 3D PrinterELEGOO Centauri Carbon is an advanced 3D printer designed for 3D printing professionals, engineers and enthusiasts. Featuring state-of-the-art CoreXY heated chamber kinematics and rugged construction, the device provides unparalleled accuracy, stability and the ability to work with a wide range of materials. With a maximum nozzle temperature of 320°C and a built-in automatic leveling system, each print is precise and perfectly reproduced, regardless of the complexity of the model.Stability at any speedThe Centauri Carbon is distinguished by a sturdy frame made of cast aluminum and additional reinforcements in the form of four aluminum alloy pillars and stainless steel side panels. This design provides excellent stability even at high printing speeds. Thus, the machine can reach speeds of up to 500 mm/s, which significantly reduces production time without sacrificing quality.Printing from demanding materialsThe use of an enclosed chamber with an active heating system allows working with demanding filaments that require stable temperature conditions. The Centauri Carbon supports a wide range of materials, including PLA, PETG, TPU, ABS, ASA and carbon fiber reinforced filaments such as PETG-CF and PA-CF. This allows users to create both flexible and extremely durable models that can withstand high temperatures and mechanical stress.Cooling system - precision in every detailCentauri Carbon is equipped with an advanced cooling system that includes a high-speed model fan, an auxiliary fan for parts and an external housing fan. This solution guarantees an optimal temperature in the chamber, which effectively prevents layer deformation and allows for extremely precise details in prints.Stable filament feeding and automatic cuttingA dual extruder made of hardened steel ensures smooth and precise material feeding, even when printing at high speeds. The built-in automatic filament cutter allows for fast and precise cutting and material reversal, eliminating the problem of clogged nozzles and improving the overall reliability of the device.CoreXY kinematics - speed and accuracyThe use of CoreXY kinematics makes the printer achieve high precision and printing speed, while reducing the weight of moving parts. As a result, Centauri Carbon not only runs faster than standard 3D printers, but also provides better detail reproduction and higher print repeatability.Automatic leveling and Z-axis compensationThe printer is equipped with an automatic calibration system, which uses four precision pressure sensors and an intelligent Z-axis compensation algorithm. As a result, the user can fully focus on designing, and the table alignment itself is done with a single click, eliminating the need for manual adjustments.Full control over printingCentauri Carbon offers the function of recording the printing process with a built-in timelapse camera. Users can monitor the print progress live, analyze any errors and document the entire process in high resolution, which is particularly useful for industrial and educational applications.A professional printer for the most demandingELEGOO Centauri Carbon is a device that will meet the needs of both hobbyists and professionals. With a combination of high printing speed, precise temperature control, automatic leveling and compatibility with a wide range of materials, this printer is an excellent choice for anyone looking for reliability and top quality prints.Included Touch screen Spool holder Filament sample Power cord Clog removal tool Allen wrench set (1.5/2.0/2.5/3.0 mm) Screwdriver Spare nozzle/heating table wiper USB Scraper blade User manual Manufacturer ELEGOO Model 50.201.020300 Body Working space 256 x 256 x 256 mm Work platform size 260 x 260 mm Product size 398 x 404 x 490 mm Gross weight 21 kg Speed Printing speed ≤ 500 mm/sec Acceleration 20000 mm/s2 Temperature Ambient temperature 5-40℃ Max heated bed temperature 110℃ Max temperature of the nozzle 320℃ Electrical req

CREALITY CR-6 SE 350W Intelligent Leveling-free DIY 3D Printer Print Size 235 x 235 x 25cm EU Plug

Anycubic Kobra 3 Max 3D PrinterAnycubic Kobra 3 Max is a state-of-the-art 3D printer designed for creatives who need a large workspace, precision and speed. Thanks to its innovative technologies and smart features, the device enables even the most demanding projects, regardless of their size. It is the ideal solution for both professionals and 3D printing enthusiasts.Spacious workspaceOne of the key advantages of the Anycubic Kobra 3 Max is its huge print space of 420 x 420 x 500 mm. It allows the creation of large models in a single run, eliminating the need to combine smaller parts. This is perfect for those doing architectural projects, industrial prototypes or decorative elements.Unmatched speed and performanceThe printer achieves a maximum print speed of 600 mm/sec, which, combined with acceleration up to 10,000 mm/sec², significantly reduces project turnaround time. The advanced LeviQ 3.0 system enables automatic leveling of the work table, and the Anti-Step Lost function prevents layers from skipping, resulting in exceptionally precise and stable prints.Precision at every stageThe Cobra 3 Max is equipped with a quick-connect Hotend, enabling printing at temperatures up to 300°C. The hotplate heats up to 90°C in just 125 seconds, speeding up the start of work. Thanks to the improved location of the filament cutter and an anti-entanglement system, users can focus solely on completing their projects.SpaciousThe printer uses advanced systems such as resonance compensation and dynamic flow, which eliminates vibration and provides even greater printing accuracy. Two Y-axis motors with double core shafts and SG15 bearings eliminate layer misalignment, and a Z-axis motor with a double screw increases design stability.Automation and safetyWith artificial intelligence tangle detection, the Kobra 3 Max immediately stops printing if there is a problem with the filament.Easy operation and software supportAnycubic Kobra 3 Max works with the intuitive Anycubic Slicer Next, based on the Orca platform. The Anycubic APP allows remote control, real-time progress monitoring and time-lapse photography. In addition, LAN mode and Wi-Fi support make it easy to integrate into a home or business network.Included Printer frame Base housing Print head Touchscreen Spool holder Cable holder Set 1- For mounting the frame Kit 2 - For mounting the support rods Kit 3 - For printhead cable Kit 4 - For printhead installation Kit 5 - For screen installation Kit 6 - For installation of spool holder Power cord (2 pcs) Cable organizer (6 pcs) USB drive (1 pc.) Filament tube (1 pc.) Allen wrench set Test filament Nozzle cleaning tool Lubricant Set of wrenches Support rod Manufacturer Anycubic Model KB3M-IP-O Printing volume 420*420*500mm Touch screen 4.3-inch Maximum print speed 600mm/second Maximum acceleration 10000mm/s² Nozzle diameter 0.4mm (0.2/0.6/0.8mm available) Auto-leveling LeviQ3.0 Auto-leveling Benchy printing 17 min 18 min Noise 60dB (standard mode) X axis motors Dual core shaft + SG15 bearing Y axis motors Dual core shaft + SG15 bearing + Dual motor Z axis motors Double motor double screw Maximum nozzle temperature 300°C Maximum hotplate temperature 90°C Belt tension Automatic Quick-connect hotend Yes LAN mode Support WiFi Support Application control Support Cutting software Anycubic Slicer Next, external Automatic resume Support AI detection AI spaghettification detection, Object skipping (requires camera) Resonance Compensation Support Dynamic flow compen Support Device weight 19 kg Device dimensions 706 x 640 x 753 mm Printing speed Recommended speed 300 mm/s; maximum speed 600 mm/s Construction platform PEI spring steel Material Kobra 3 Max supports PLA, PETG, ABS and TPU Power supply 300W Connection method Wi-Fi, AC Cloud, local network Cooling fan rotation 7000 RPM.

Creality Ender-3 S1 Plus Full-metal Dual-gear Larger-size 3D Printer EU Plug