Monitor 38

IMOU AOV PT KIT Outdoor Pan-Tilt IP CameraThe IMOU AOV PT KIT 5MP is a pan-tilt outdoor camera that combines 5 MP resolution (2880 × 1620), a full range of motion of 340° horizontally and 90° vertically, and independent power supply thanks to a 10,000 mAh battery and a 5 W solar panel. Support for 2.4 GHz Wi-Fi and 4G LTE ensures connectivity even in areas without access to a wired internet connection, and the pre-installed 32 GB card allows you to start recording immediately after startup. Thanks to AOV technology, the device enables 24/7 monitoring with optimized power consumption. The IP66-rated design provides effective protection against rain, dust, and changing weather conditions. This allows the camera to operate reliably year-round.Uninterrupted MonitoringThe use of Always-on Video (AOV) allows for continuous monitoring of the surroundings while reducing energy consumption. The camera creates time-lapse recordings from regularly taken photos, and automatically switches to full video recording when an event is detected. This solution allows you to maintain a complete picture of the situation while extending battery life.Energy Independence and Off-Grid OperationThe built-in 10,000 mAh battery, combined with a 5 W solar panel, enables operation without the need to connect to the electrical grid. As little as about 2 hours of daily sunlight can cover the camera’s power needs during standard use, eliminating the need for frequent charging. Additionally, the notification system alerts you when the battery level drops to 20% and 10%, allowing you to take action in a timely manner.Stable connectivity in all conditionsThe camera offers two operating modes—2.4 GHz Wi-Fi and 4G LTE—making it suitable for use both at home and in locations without constant internet access. Support for European LTE bands (B1/3/5/7/8/20/28/38/40/41) ensures broad compatibility with carriers. This solution is particularly useful on plots of land, construction sites, or in facilities located far from network infrastructure.Smart Detection and Active ResponseImou Sense algorithms enable human detection with over 98% accuracy, reducing false alarms. The Auto Tracking feature automatically tracks a detected person, keeping them in the frame. In case of a threat, the camera activates a siren and spotlights, increasing the effectiveness of deterring intruders.Clear imageThe camera is equipped with a 1/3” CMOS sensor and a 3.6 mm lens, offering a viewing angle of 76° (H), 41° (V), and 91° (D). Night vision range of up to 20 m allows you to monitor the area even after dark, and the 8x digital zoom makes it easy to zoom in on details. The rotating design eliminates blind spots and enables full coverage of the monitored area.Two-way real-time communicationThe built-in microphone and speaker enable two-way communication, allowing you to respond immediately to situations in front of the camera. This practical solution lets you not only monitor but also communicate with household members or deter unwanted visitors.Convenient data storageThe camera supports microSD cards up to 512 GB, and the included 32 GB card lets you get started right away. Recordings are stored locally—this solution gives you full control over your data and eliminates the need for additional fees.Included: Camera Solar panel Power cable (1 m) Installation template Mounting bracket Pack of screws and wall plugs Universal joint Mounting base Round socket nut Screw lock nut Screws x4 Additional wall plugs x3 User manual General Manufacturer IMOU Model IPC-B7ED-5M1TEA-EU/F Material Plastic Power supply DC 5V 2A / solar panel Power consumption

MERACH MR-T21B1 Electric Treadmill (Black)The MERACH MR-T21B1 is a modern electric treadmill designed for people who want to train comfortably at home – without compromising on power, durability, and functionality. Equipped with a powerful 2.5 HP motor (max. 1.95 HP), it reaches speeds of up to 6.44 km/h while operating extremely quietly (

MERACH MR-2440P1 vibration platform (pink)The MERACH MR-2440P1 vibration platform (pink) is a modern home training center that combines 200 W of power, 13 mm vibration amplitude, a wide 72 cm platform, a load capacity of up to 200 kg, and smart Auto On/Off and Bluetooth functions. The stable construction with a non-slip surface, clear LED display, shock absorption, and built-in speaker allow you to train effectively, safely, and comfortably—exactly how you like it. This compact device activates deep muscle groups and helps you achieve visible results faster without leaving home.Full control thanks to smart start and pauseThe MERACH MR-2440P1 is equipped with a built-in gravity sensor that automatically starts the device when you step on the platform and gently move side to side. When you step off the device, it goes into pause mode after 30 seconds and automatically turns off after 10 minutes. This is not only convenient, but also saves energy and ensures safe use.Customize your workout with three adjustable intensity levelsDifferent foot settings allow you to adjust the intensity of the vibrations. A narrower setting provides gentler vibrations ("Walking - Relax" mode), a wider setting increases their power ("Running - Strong" mode), and the intermediate position offers a comfortable "Jogging - Comfortable" workout. This allows you to move freely from a relaxing session after work to intense muscle activation - without changing equipment.Deep muscle activation with 200 W of power and 13 mm amplitudeAt the heart of the device is a powerful 200 W motor that generates vibrations with an amplitude of 13 mm. These parameters translate into deep muscle stimulation – even those that are difficult to reach during classic training. The result? Better muscle tone, improved circulation, support for body shaping, and greater effectiveness of every minute of exercise.Stability and safety – train confidently, without worryThe platform has been designed for maximum stability. Non-slip suction cups prevent the device from moving, and the shock-absorbing design reduces shocks and vibrations transmitted to the floor. The wide surface (72 × 38 cm) ensures comfort even for people with a larger body build, and the maximum load capacity of 200 kg allows you to train without restrictions.User-friendly surface and clear displayThe soft, skin-friendly silicone mat increases grip and comfort during exercise, even when barefoot. The centrally located LED display allows you to monitor the time and operating mode in real time. Everything is intuitive and clear, so you can focus solely on your workout.Training with music – built-in BluetoothThe built-in Bluetooth module (2.4 GHz) allows you to connect the platform to your smartphone and play your favorite music while exercising. Training becomes a pleasure, and the rhythm helps you stay motivated. It's a detail that really affects your regularity and commitment.Included in the set MERACH MR-2440P1 vibration platform x1 Remote control x1 Resistance band x1 Power cord x1 User manual x1 Manufacturer MERACH Model MR-2440P1 Rated power 200 W Vibration amplitude 13 mm Maximum load 200 kg (440 lbs) Device dimensions 72 × 38 × 16 cm (720 × 380 × 160 mm) Net weight 10.5 kg (23 lbs) Platform width 72 cm Power supply 220–240 V ~ 50/60 Hz Display LED Wireless connectivity Bluetooth

IMOU AOV PT KIT 4G Outdoor IP Camera (without card)The IMOU AOV PT KIT 5MP is a pan-tilt outdoor camera that combines 5 MP resolution (2880 × 1620), a full range of motion of 340° horizontally and 90° vertically, and independent power supply thanks to a 10,000 mAh battery and a 5 W solar panel. Support for 2.4 GHz Wi-Fi and 4G LTE ensures connectivity even in areas without access to fixed-line internet. Thanks to AOV technology, the device enables 24/7 monitoring with optimized power consumption. The device supports microSD cards up to 512 GB. Recordings are stored locally—this solution provides full control over data and eliminates the need for additional fees.Uninterrupted monitoringThe use of Always-on Video (AOV) allows for continuous monitoring of the surroundings while reducing energy consumption. The camera creates time-lapse recordings from regularly taken photos, and automatically switches to full video recording when an event is detected. This solution allows you to maintain a complete picture of the situation while extending battery life.Energy Independence and Off-Grid OperationThe built-in 10,000 mAh battery, combined with a 5 W solar panel, enables operation without the need to connect to the electrical grid. As little as about 2 hours of daily sunlight can cover the camera’s power needs during standard use, eliminating the need for frequent charging. Additionally, the notification system alerts you when the battery is low.Stable connectivity in all conditionsThe camera offers two operating modes—2.4 GHz Wi-Fi and 4G LTE—making it suitable for use both at home and in locations without constant internet access. Support for European LTE bands (B1/3/5/7/8/20/28/38/40/41) ensures broad compatibility with carriers. This solution is particularly useful on plots of land, construction sites, or in locations far from network infrastructure.Smart Detection and Active ResponseIMOU SENSE algorithms enable the detection of people and vehicles. In case of a threat, the camera activates a siren and a light alarm (spotlights and red and blue lights). Additionally, the Privacy Mode feature allows you to cover the lens to protect privacy.Clear imageThe camera is equipped with a 1/3” CMOS sensor and a 3.6 mm lens, offering a viewing angle of 76° (H), 41° (V), and 91° (D). Night vision range of up to 25 m allows you to monitor the area even after dark, and the Smart Full-Color Night Vision feature provides a color image when motion is detected. The rotating design eliminates blind spots and enables full coverage of the monitored area.Two-way real-time communicationThe built-in microphone and speaker enable two-way communication, allowing you to respond immediately to situations in front of the camera. This practical solution lets you not only monitor but also communicate with household members or deter unwanted visitors.Included in the set: Camera Solar panel Mounting bracket (for the camera) Mounting bracket (for the panel) Installation template Power cable (1 m) Pack of screws and anchors (for the camera) Pack of screws and anchors (for the panel) User manual General Manufacturer IMOU Model IPC-B7ED-5M0TEA-EU Material Plastic Power supply DC 5V 2A Operating temperature -20°C to +50°C Charging temperature -10°C to +45°C Dimensions 177 × 110 × 142 mm Certifications CE, MSDS Camera Sensor 1/3” Progressive CMOS Resolution 5 MP (2880 × 1620) Night vision range 25 m Lens 3.6 mm Viewing angle 76° (H), 41° (V), 91° (D) Pan/tilt range 340° / 90° Battery 10,000 mAh Video and Audio Video Compression H.265 Frame Rate Up to 15 fps Digital Zoom 8× Audio Two-way Notification Management Human Detection Yes Vehicle Detection: Yes Low battery notification Yes Storage Local storage MicroSD up to 512 GB Network Wi-Fi IEEE802.11 b/g/n, 2.4 GHz 4G LTE B1/3/5/7/8/20/28/38/40/41 App Imou (iOS, Android) Additional interfaces Microphone and speaker Built-in Reset button Yes Memory card slot Yes

The FALCAM F22 & F38 Quick Release Camera Cage for Canon EOS C50 is a modular aluminum cage designed to protect the camera while expanding mounting options through the F22 and F38 quick release ecosystems. It supports fast horizontal-to-vertical switching, retains full access to camera controls, and includes multiple ARRI-style mounting points for professional rig builds. The FALCAM F22 and F38 Quick Release Camera Cage for Canon EOS C50 is a professional-grade modular rigging solution designed to enhance protection, flexibility, and workflow efficiency for filmmakers using the Canon EOS C50. Precision-engineered from durable aluminum alloy, the cage provides a form-fitted structure that safeguards the camera body while maintaining full access to all buttons, ports, and operational controls. Built around the FALCAM F22 and F38 quick release ecosystems, the cage enables rapid transitions between handheld, tripod, and rig setups. Its modular architecture supports quick horizontal-to-vertical switching, making it ideal for dynamic shooting environments where speed and adaptability are essential. The cage features a detachable top plate compatible with XLR-style top handles, along with extensive mounting options across all sides. Multiple 1/4"-20 threaded holes with ARRI locating points allow secure attachment of accessories such as monitors, lights, articulating arms, and wireless systems. Integrated cold shoe mounts further expand compatibility for compact accessories. For improved usability in professional workflows, the cage includes a magnetically attached wrench stored directly on the base, ensuring tools are always available without interrupting production. Anti-slip padding protects the camera body from wear, while integrated cable management clamps secure HDMI and other connections to prevent accidental disconnection during operation. The modular design allows full customization of rig configuration, with F22 and F38 quick release mounts distributed across the top, bottom, and sides for maximum flexibility. Key Features Form-fitted design for Canon EOS C50 Compatible with FALCAM F22 and F38 quick release systems Modular structure for full cage or partial rig configurations Quick horizontal-to-vertical switching support Detachable top plate compatible with XLR top handles Multiple 1/4"-20 ARRI locating threaded mounting points Integrated cold shoe mount for accessories Built-in cable clamps for HDMI and accessory cable management Magnetic wrench storage for on-the-go adjustments Anti-slip padding to protect camera body Aluminum alloy construction for durability and strength 1 × FALCAM F22 & F38 Quick Release Camera Cage for Canon EOS C50 1 × Detachable Top Plate 1 × Side Mounting Plates (as configured) 1 × Cable Clamp Set 1 × Magnetic Wrench Tool 1 × Installation Hardware Kit Brand: FALCAM Product: F22 & F38 Quick Release Camera Cage for Canon EOS C50 Compatible Camera: Canon EOS C50 Material: Aluminum Alloy Quick Release Systems: F22 / F38 ecosystem compatible Mounting Points: Multiple 1/4"-20 threaded holes ARRI locating holes Cold shoe mount Design: Modular (full cage / partial configurations) Top Plate: Detachable, XLR handle compatible Cable Management: HDMI + universal cable clamp system Tools: Magnetic wrench included

The Falcam Quick Release Camera Cage for Nikon ZR is a full aluminum alloy protective rig designed to expand mounting options while maintaining full access to camera controls, ports, and the hot shoe. Supporting both F22 and F38 quick release ecosystems, it integrates multiple threaded mounts, a removable ergonomic handgrip, cold shoe, and cable management features for a professional cinema setup. The Falcam Quick Release Camera Cage for Nikon ZR is a modular, precision-machined aluminum rig built to enhance protection, stability, and expandability for the Nikon ZR cinema camera. It is designed around Falcam’s F22 and F38 quick release ecosystems, enabling fast transitions between tripods, gimbals, and accessories while preserving full access to essential camera functions. The cage consists of a baseplate, right side plate, and top plate, all engineered for a secure fit with anti-slip buffer pads that protect the camera body. Its lightweight aluminum alloy construction ensures durability without adding unnecessary bulk, making it suitable for handheld, rigged, or stabilized shooting setups. A standout feature is its wide range of mounting options. Multiple anti-twist 1/4"-20 threaded holes across the top and sides allow the attachment of monitors, articulating arms, wireless receivers, and other accessories. A built-in cold shoe mount provides additional flexibility for microphones or lights, while integrated lanyard and wrist strap holes improve handling safety during handheld use. The cage also includes a removable ergonomic handgrip, offering improved comfort and control during extended shooting sessions. A micro-HDMI cable clamp is integrated to secure connections and prevent accidental disconnections during production. For workflow efficiency, the cage incorporates Falcam F22 quick release mounting points on the top and sides, along with F38 compatibility on the base and selected side interfaces. A magnetic wrench is stored directly in the base, ensuring quick adjustments without carrying extra tools. Key Features Compatible with Nikon ZR cinema camera Full cage design: baseplate, side plate, and top plate Supports Falcam F22 & F38 quick release systems Multiple anti-twist 1/4"-20 threaded mounting points Built-in cold shoe mount for accessories Removable ergonomic handgrip for improved handling Maintains full access to camera ports, controls, and hot shoe Micro-HDMI cable clamp for secure connections Magnetic wrench stored in cage base for quick adjustments Anti-slip padding for camera protection and stability Lightweight and durable aluminum alloy construction 1 × Full Camera Cage (Baseplate + Side Plate + Top Plate) 1 × Removable Handgrip 1 × Micro-HDMI Cable Clamp 1 × Magnetic Wrench (integrated in base) Mounting hardware (included by manufacturer) Material: Aluminum Alloy Dimensions: 6.2 × 4 × 2.7 in (158 × 101.5 × 67.4 mm) Weight: 9.9 oz (280 g) Camera Compatibility: Nikon ZR