PC Hub

Meross MSS715MA-UN WiFi Smart Switch (Matter)Meross MSS715MA-UN is a compact WiFi smart switch that allows you to easily convert traditional electrical appliances into smart home system components. It only takes about 20 minutes to upgrade an existing installation - without the need to purchase new equipment. The switch supports the Matter standard, which ensures wide compatibility, fast response and high security.Intelligent power managementThe device supports power consumption monitoring, allowing you to optimize the performance of connected devices. You can plan precise work schedules that will be carried out even without a network connection. This will give you more control over power consumption and save on your bills! Note: energy consumption monitoring is only available in the Meross app.Full remote and local controlControl your connected devices from anywhere - using the Meross app or voice commands. With integration with Apple HomeKit, Google Home and Amazon Alexa, you can turn your device on or off without even getting up from the couch. Local scenarios and automations that operate independently of the internet are also supported.Compact design and performanceThe MSS715MA-UN switch supports a load of up to 3,800 watts and 16 amps, so it will also be suitable for devices with high power consumption. In addition, the V0-class flame-retardant PC plastic housing and built-in overheat protection ensure safe use.Stability and safety with MatterThanks to the Matter standard, the switch operates in a local architecture, which provides greater privacy, better stability and faster response. Note: a compatible Matter hub, such as the HomePod mini, Echo Dot or Google Nest Hub, is required for the device to work. Manufacturer Meross Model MSS715MA-UN Matter standard support Yes Compatibility Meross app, Apple HomeKit, Google Home, Amazon Alexa Energy consumption monitoring Yes (only with Meross app) Max load 16 A 3800 W Dimensions 96 × 47 × 24 mm Connectivity 2.4 GHz Wi-Fi

SONOFF SNZB-05P ZigBee flood/water leak sensor kit + WLDC200 cable.The SONOFF SNZB-05P kit with WLDC200 cable is a comprehensive solution that effectively protects your home from flooding and water leaks. The SNZB-05P sensor, using the ZigBee 3.0 protocol, is distinguished by its high-precision operation and corrosion resistance thanks to its gold-plated probes and IP67-rated design. The WLDC200 extension cable significantly increases the monitoring range and enables water detection even in hard-to-reach areas such as basements, under HVAC systems or around water heaters. Together, they form a reliable duo that can detect even the smallest leaks in time and minimize the risk of costly damage.Advanced technology and reliable performanceThe SNZB-05P sensor is equipped with a concave water-collecting design that provides precise moisture detection as small as 0.5 mm. The IP67 rating and gold-plated probes, tested for corrosion resistance, guarantee reliability even in harsh environments. The WLDC200 cable allows wide-range monitoring and serial connection, allowing flexible installation without length restrictions. It is an ideal solution not only for homes, but also industrial facilities.Smart notifications and compatibility with Smart Home systemsThe kit offers smart notifications via the eWeLink app, an audible alarm via ZigBee gateway, and email (for eWeLink Advanced subscribers). Leak information is sent every 10 minutes, eliminating the risk of missed alerts. The device works with popular smart home platforms such as Amazon Alexa, Google Home, SmartThings and IFTTT, providing full integration with your home management system.Full control and flexibilityThe WLDC200 cable is an indispensable accessory that allows you to monitor large areas and precisely inspect leak-prone areas. The ability to connect cables in series provides unlimited configuration possibilities, allowing you to fit the system into any space. Whether securing a bathroom, laundry room, kitchen or basement, the SONOFF SNZB-05P kit with WLDC200 cable guarantees maximum safety and peace of mind.The kit includes extension cable water leakage sensor cable clamps x3 instruction manual Cable Manufacturer Sonoff Model WLDC200 Compatible sensor models SNZB-05P Operating temperature -10°C - 60°C Operating humidity 0-80%RH Material PC, ABS Length 2 m Weight 32 g Sensor Manufacturer Sonoff Model SNZB-05P Communication protocol ZigBee 3.0 Power supply CR2477 3V battery (included) Battery life Up to 5 years Detection range Water level from 0.5 mm Operating temperature -10°C ~ 60°C Working humidity 0 ~ 100% RH Housing material PC + ABS Product dimensions 48 x 48 x 21.6 mm Net weight 45 g Communication range 130 m (in open space) Support for Home Assistant Yes (integration via ZHA or Zigbee2MQTT) Supported ZigBee gateways iHost, ZBDongle-P/E, NSPanelPro, AeoTec Smart Home Hub V3, SmartThings Hub V3, ZBBridge-U/P Compatibility with platforms Amazon Alexa, Google Home, SmartThings, IFTTT Protection class IP67 (waterproof and dustproof) Notifications eWeLink app (push), audio alert via ZigBee gateway, email notifications (requires subscription to eWeLink app)

Smart wall switch for blinds SONOFF MINI-RBS-E MatterSONOFF Orb-RBS is a smart wall switch designed for convenient control of blinds, curtains and shutters. The device is part of the Fusion series and works with Matter over Wi-Fi technology, which ensures broad compatibility with popular smart home platforms. This allows you to integrate it with Apple Home, Google Home, Alexa, Samsung SmartThings or Home Assistant, all using one common standard. Only the Matter hub is required for it to work - once added, you can manage blinds throughout your home from a single app.Precise controlOrb-RBS allows you not only to open and close the blinds, but also to adjust them precisely within a selected range - for example, 30% for gentle brightening in the morning or 70% in bright sunlight. With the slider available on the mobile app, you can smoothly and precisely adjust the position of the blinds as you are comfortable.Voice and local controlThe switch works locally, even if the internet is temporarily down. If you're using a voice assistant at home-for example, Alexa, Siri or Google Assistant-you can use a single voice command to close the blinds at exactly 60% or completely open them without moving from your seat.Automations and schedulesOrb-RBS allows you to create simple and advanced scenes and schedules. You can set the blinds to automatically raise at 7:00 in the morning and close at 8:00 in the evening - helping to maintain the natural rhythm of the day, as well as save energy. Combining with a door sensor or motion sensor also allows you to create privacy-enhancing scenes - the blinds can close themselves when you leave the house.Easy and quick installationInstallation of the switch is simple and possible in both type 86 boxes and standard round boxes (⌀60 mm). You can mount it alone or in a multi-module frame - horizontally or vertically - depending on the interior layout. This way the device not only works practically, but also looks good in any room. Manufacturer Sonoff Product name Orb-RBS Series Fusion Model MINI-RBS-E Microcontroller (MCU) ESP32 Power supply 100-240V~, 50/60Hz, max. 1A (motor) Wireless connectivity IEEE 802.11 b/g/n, 2.4 GHz (Wi-Fi) Weight 84,7 g Dimensions 86 × 86 × 34 mm Color White Case material PC plastic (polycarbonate) Recommended wire diameter From 18AWG to 14AWG (copper, solid or wire only) Place of application For indoor use Working temperature From -10°C to +40°C Working humidity 5-95% RH, non-condensing

SONOFF ZBMINIL2-E ZigBee smart wall switchOrb-ZBW1L is a wall switch from the Fusion series that works with ZigBee technology and does not require a neutral wire. This is a great option for older installations. With compatibility with popular ZigBee hubs, you can easily automate the lighting in your home without having to replace the entire electrical system. Thanks to its compatibility with Fusion series frames, it can be easily mounted vertically or horizontally - either individually or next to other devices. Fits standard boxes: round (⌀60 mm) and square (Type 86).No neutral wireThanks to ZigBee technology and internal power supply from a single phase, Orb-ZBW1L is ideal for apartments and houses where there is no neutral wire in the box. Installation is quick and clean, without forging walls or running additional wires.Works with popular smart home platformsThe device works with ZigBee hubs such as SONOFF ZBBridge-P/U, NSPanel Pro, iHost, SmartThings, Zigbee2MQTT, as well as Amazon Echo devices with built-in ZigBee hub (e.g. Echo 4th Generation, Echo Show 2nd Gen). This allows you to control the lights using Alexa, Google Home or the eWeLink app.Smart scenes and group controlThe switch can be easily integrated with wireless sensors and buttons. This allows you to create automations such as: the light turns on when a door is opened, when motion is detected in the hallway, or with one click before bedtime. In addition, the grouping function allows you to control multiple switches simultaneously from a single app. Manufacturer Sonoff Product name Orb-ZBW1L Series Fusion Model ZBMINIL2-E Microcontroller (MCU) EFR32MG22 Power supply 100-240V~, 50/60Hz, 6A (maximum resistive load) LED load Up to 150W at 100V / up to 300W at 240V Maximum load 1440W Minimum load 3W Wireless connectivity Zigbee 3.0 Weight 80 g Dimensions 86 × 86 × 35.8 mm Color White Housing material PC plastic (polycarbonate) Recommended wire diameter 16AWG to 14AWG (copper, solid or stranded wire only) Application For indoor use Operating temperature range From -10°C to 40°C Operating humidity range 5-95% RH, non-condensing

SONOFF MINIR4M-E Matter smart wall switchThe SONOFF Orb-MW1 is a 1-channel wall switch from the Fusion series that combines a minimalist design with full compatibility with the Matter ecosystem. It works independently of your internet connection, which means you can turn on the light even if your router stops working. It works with Apple Home, Google Home, Alexa, SmartThings and Home Assistant - making it perfect for any smart home.Matter interoperability - one device, multiple systemsThe switch works with Matter, which allows for easy integration with multiple smart home platforms - so you can control the lights by voice using Siri, Alexa or Google Assistant. Everything is done through a common Matter hub, which makes it easier to manage devices and improves operational stability. In addition, Orb-MW1 works with door sensors, motion sensors or schedules, allowing you to create automatic scenes. The light can turn on when the door is opened, when motion is detected at night or with one click before bedtime.Local controlThe switch operates locally, independent of the Internet. If the network stops working, you can still manually turn the light on or off - exactly like a classic switch. This way you can be sure that the light will work whenever you need it.Detach Relay functionIn Detach Relay mode, turning off the switch does not cut off power to the smart bulbs. They remain online all the time and ready for automation or control from an app. This is especially useful if you use smart scenes, schedules or voice control. Manufacturer Sonoff Name Orb-MW1 Series Fusion Model MINIR4M-E Microcontroller (MCU) ESP32-C3FN4 Power supply 100-240V~, 50/60Hz, max. 10A (resistive load) Wi-Fi IEEE 802.11 b/g/n, 2.4 GHz Weight 84 g Dimensions 86 × 86 × 34 mm Color White Housing material PC Recommended wire diameter 16AWG to 14AWG, copper wire only (solid or wire) Application Indoors Operating temperature range From -10°C to 40°C Working humidity 5-95% RH, non-condensing

SONOFF MINI-ZB2GS-E ZigBee two-channel wall switchSONOFF MINI-ZB2GS-E is a state-of-the-art ZigBee 3.0 two-channel wall switch designed for stable, fast and safe control of lighting and other electrical circuits. It allows independent control of two loads, acts as a ZigBee router to amplify a mesh network, offers Detach Relay mode, support for scenes, schedules, voice control and integration with popular smart home platforms - all in a sleek, minimalist flush-mount form.Stable ZigBee 3.0 communication and dual channel supportThe switch uses the ZigBee 3.0 protocol (IEEE 802.15.4), ensuring low latency and high reliability of operation. Importantly, the device acts as a ZigBee Router, thus strengthening and extending the range of the mesh network in the home. The ceramic antenna used and the Enhanced / Turbo Mode further improve the stability of the connection, which translates into more reliable operation of the entire smart home system - especially in larger apartments and houses. In addition, the dual-channel design allows you to control two circuits from a single point, such as a ceiling lamp and a table light, or two light zones in one room. Such a solution means fewer switches on the wall, a consistent look and more convenience on a daily basis - both for manual control and from the app. Each channel can be configured independently - including automation and scenes.Detach Relay mode - ideal for smart bulbsThe detach relay function ensures that the physical button does not cut off power, but only sends a control command. As a result, smart bulbs do not lose their connection to the network and do not go offline after using a wall switch. In addition, it is possible to use ZigBee Binding, i.e. to directly bind a button to another ZigBee device - without the involvement of the cloud, which ensures immediate response even if the Internet is temporarily absent.Scenes, schedules and automationsThe MINI-ZB2GS-E allows you to create smart scenes - such as automatically turning on lights when motion is detected, or delaying switching on when power is applied. The user can specify the device's behavior when power is restored (Power-On State), including setting a delay to turn on the light, which prevents it from accidentally turning on after a power outage. Schedules and timers allow the lighting operation to be matched to the rhythm of the household members' day, increasing comfort and a sense of security.Broad compatibility with smart home platformsThe device works with the eWeLink app and Home Assistant (ZHA and Zigbee2MQTT), offering extensive configuration options for more advanced users. It can be used with a number of ZigBee hubs, including ZBBridge-P, ZBBridge-U, NSPanel Pro, iHost and ZigBee donglers (ZBDongle-P/E, Dongle Plus MG24, Dongle Lite MG21). It also supports voice control via Amazon Alexa and Google Home. Integration with Apple Home is only possible via Matter Bridge - requires a compatible Matter gateway and a suitable environment (e.g. eWeLink CUBE).Safety, durability and easy operationA housing made of fire-resistant PC plastic, overvoltage and overheat protection, and a long-life relay (up to 100,000 cycles) make the switch suitable for heavy daily use. CE and RoHS certifications confirm the high quality of manufacture. The switch fits standard type 86 mounting boxes and European round boxes (Ø60 mm). Configuration is done in a few steps in the eWeLink app - a compatible ZigBee hub is required for operation, which allows the device to communicate with the smart home system. The SONOFF MINI-ZB2GS-E also supports remote OTA software updates, allowing you to develop its features without disassembly.Included: SONOFF MINI-ZB2GS-E ZigBee two-channel wall switch Mounting screws User manual Manufacturer SONOFF Model MINI-ZB2GS-E Communication protocol ZigBee (IEEE 802.15.4) Housing material PC Operating temperature from -10°C to 40°C Power supply / electrical parameters 110-240 V~50/60 Hz10 A / channelmax. 16 A total

SONOFF MINI-2GS-E Matter two-channel wall switchThe SONOFF MINI-2GS-E is a state-of-the-art two-channel wall switch based on 2.4 GHz Wi-Fi connectivity, designed for smart control of lighting and other electrical circuits in the home. It allows independent control of two loads from a single point, combining classic physical push-button operation with Matter's advanced smart home features. Thanks to local LAN communication, the device responds quickly and operates stably even without internet access, providing convenience, reliability and full integration into the modern smart home ecosystem.Matter and full ecosystem compatibilityThe switch supports the Matter standard, so it can be integrated with platforms such as Apple Home, Google Home, Amazon Alexa, SmartThings and Home Assistant. Note: a compatible Matter hub is required to operate in the Matter ecosystem, which mediates the communication of devices on the network. Alternatively, the device can be added to the eWeLink app to access settings and automation from one place.Independent control of two circuitsThe dual-channel design allows you to control two loads simultaneously - for example, two light points or a lamp and an outlet - without the need to install additional switches. Each channel operates independently, increasing installation flexibility and facilitating upgrades to existing electrical systems.Automations, schedules and scenesThe MINI-2GS-E allows you to create time schedules, smart scenes and automations that adapt lighting operation to the daily rituals of household members. Among other things, you can set the switch to automatically turn on the lights after dark, decide whether the lights should turn on by themselves after a power outage and return, and associate the switch's operation with other smart home devices. These features are available by adding the device to the eWeLink app or a compatible Matter platform.Local and voice controlThe switch allows for local (LAN) control, which means quick responses and reliable operation even when the Internet is temporarily unavailable. When integrated with suitable smart home platforms, voice control is also possible, such as with Amazon Alexa, Google Assistant or Siri - this requires a compatible hub and a voice speaker.Special features for greater controlThe MINI-2GS-E offers additional features, such as Detach Relay mode, Power-on State settings and Inching mode. These allow the switch's operation to be tailored to specific installation scenarios and enhance safety and user comfort.Safe mounting and trouble-free installationThe MINI-2GS-E is designed to make installation simple and predictable, and daily use safe. A housing made of fire-resistant PC plastic and overvoltage, overload and overheat protection features enhance operational safety. The device meets CE and RoHS standards. It fits both Ø60 mm European mounting boxes and Type 86 boxes and supports installations with a neutral conductor (L + N), and the clever terminal layout makes it easy to connect two circuits and integrate with classic wall switches.Included: SONOFF MINI-2GS-E two-channel wall switch Mounting screws Operating instructions Manufacturer SONOFF Model MINI-2GS-E Communication standard Matter over Wi-Fi (IEEE 802.11b/g/n 2.4 GHz) Housing material PC Operating temperature from -10°C to 40°C Power supply / electrical parameters 110-240 V~ 50/60 Hz10 A / channelmax. 16 A total (resistive load) Dimensions 86 × 86 × 33.7 mm

Sonoff ZBMINI ZigBee smart switch (2 pcs).Do you want to manage your equipment more easily? With the Sonoff switch it will be possible! With its help you will get control over lighting. It is distinguished by its small size, so you can easily install it in different mounting boxes, and it also works with different types of switches. What's more, you can control it with your voice, as it is compatible with Google Home or Amazon Alexa. The set includes 2 switches.Smart switchThe ZBMINI Extreme switch is distinguished by its small size, which means you can install it in various mounting boxes, even the smallest one - EU/86/120. Moreover, it works with various types of external switches such as rocker switch or wall switch with buttons. The Sonoff device is also easy to install and does not require a neutral wire.Multiple control optionsThe Sonoff smart switch has bidirectional control capabilities. You can easily connect it to your stairwell lighting. What's more, for even easier control, you can create smart scenes, and with the Timer function, you can set when you want the lights to turn on, off, or schedule timed loops.Simplicity and reliabilityFor added convenience, the Sonoff switch has voice control capabilities, as it demonstrates compatibility with Google Home, Amazon Alexa or Alice. What's more, you don't have to worry about Internet problems, as the Sonoff brand device, with its Zigbee 3.0 switch, can connect to a Zigbee Hub and create a home LAN. In addition, you have the ability to control the lighting even if its power is only 3 watts.Quick startConnecting the smart switch is very easy. All you have to do is connect it with the right device and then download the eWeLink app. Now all you have to do is pair your phone and the equipment using Bluetooth technology. This allows you to exercise control over your entire home even if you are at work or shopping.Security guaranteeThe ZBMINI switch is a guarantee of safety, which is why its housing is made of PC plastic with a fire resistance rating of V-0. What's more, the terminal blocks guarantee the safety of the wires and ensure their reliable connection. The switch is also equipped with EFR32MG22 core, which features low power consumption. All this means that you can safely use the ZBMINI smart switch. Manufacturer Sonoff Model ZBMINIL2 Wireless connection Zigbee 3.0 Dimensions 39.5 × 32 × 18.4 mm Material PC V0 Input 100-240V ~ 50/60 Hz 6 A max. Output 100-240V ~ 50/60 Hz 6 A max. Number of pieces included 2

SONOFF MINI-ZB2GSL-E ZigBee two-channel wall switch (without neutral wire)SONOFF MINI-ZB2GSL-E is a state-of-the-art ZigBee 3.0 two-channel wall switch designed specifically for installations without a neutral wire (No Neutral). It allows independent control of two lighting circuits, offers support for scenes, schedules and voice control, while maintaining a minimalist, aesthetically pleasing flush-mount design. It is an ideal solution for upgrading older electrical installations without the need for additional wiring.Installation without a neutral wire - maximum possibilitiesThe switch is designed to operate without connecting an N wire, which significantly simplifies installation in older buildings and apartments. It does not require an additional capacitor, making installation faster and simpler. The minimum load per channel is 3 watts, which ensures stable operation with most standard light sources. Note: the switch is designed to control classic lighting only - it is not compatible with smart bulbs, dimmable bulbs or inductive loads.Two channels, scenes, schedules and moreThe dual-channel design allows you to control two independent circuits, such as a ceiling lamp and a wall lamp, or two light zones in one room. This solution guarantees fewer switches on the wall, greater visual consistency and convenience of use - both manually and from the app. The MINI-ZB2GSL-E also supports smart scenes, schedules and timers, enabling full lighting automation. There is also a Power-On State function, which allows you to specify the behavior of the light after a power outage and return - such as leaving it off or turning it on with a delay. This is a practical solution for increased comfort and safety of use.ZigBee Binding - fast and reliable local controlThe device supports ZigBee Binding, which is the direct linking of a switch to another ZigBee device (e.g. a relay or lighting) in systems such as Home Assistant (ZHA, Zigbee2MQTT). This makes control local without the cloud, ensuring immediate response and reliability even in the absence of internet.Broad compatibility with smart home platformsThe switch works with the eWeLink app and Home Assistant (ZHA and Zigbee2MQTT). It is compatible with a wide range of ZigBee hubs, including Zigbee Bridge Pro, Zigbee Bridge Ultra, iHost, NSPanel Pro and popular ZigBee dongles (ZBDongle-P/E, Dongle Plus MG24, Dongle Lite MG21). It supports voice control via Amazon Alexa and Google Home, and integration with Apple Home is possible via Matter Bridge (a compatible Matter gateway is required, such as in the eWeLink CUBE ecosystem). The MINI-ZB2GSL-E operates as a ZigBee end device (end device) and does not act as a network router.Safety, durability and ease of installationA housing made of fireproof PC plastic, overload protection and a long-life relay (up to 100,000 cycles) ensure safe and stable use for years. The device complies with CE and RoHS standards and fits standard type 86 mounting boxes and European round boxes (Ø60 mm). Configuration is done in a few steps in the eWeLink app - a compatible ZigBee hub is required for operation. The device also supports remote OTA software updates, which enable feature development without disassembly.Included: SONOFF MINI-ZB2GSL-E ZigBee two-channel wall switch (without neutral wire) Mounting screws Operating instructions Manufacturer SONOFF Model MINI-ZB2GSL-E Communication protocol ZigBee (IEEE 802.15.4) Housing material PC Operating temperature from -10°C to 40°C Power supply / electrical parameters 110-240 V~50/60 Hz8 A / channelmax. 12 A total (resistive load) Dimensions 86 × 86 × 33.7 mm