Pla cf

Creality SpacePi X4 Filament DryerCreality SpacePi X4 is a powerful dual-chamber filament dryer, allowing you to dry as many as 4 spools simultaneously with full temperature control from 45 to 85°C. Thanks to the active drying technology, fast heating and quiet operation, you will prepare PLA, PETG, TPU, ABS or PA-CF filaments for printing in a reproducible and stable way, eliminating the problem of moisture, bubbles and shagging during printing.Dry a variety of filamentsThe device features two independently controlled heating chambers, allowing you to set different temperatures for different filaments (e.g. 50°C for PLA and 85°C for PA-CF). You can use one or both chambers as needed, which saves time and energy in a small workshop or when working with different materials at the same time.Speed and uniformityWith 200W + 200W PTC heaters, SpacePi X4 heats up to 85°C in about 20 minutes. The 360° air circulation ensures even heat distribution, and the SpaceDry 4.0 technology with active dehumidification and desiccant regeneration guarantees effective moisture removal without changing cartridges.Quiet, cheap, efficientThe Active Silent system keeps noise levels to just 43-46 dB, allowing you to work comfortably at home and in the workshop. The Creality SpacePi X4 offers energy-efficient operation with an energy consumption of 0.124 kWh in single-chamber mode and 0.208 kWh in dual-chamber mode, reducing the cost of preparing filaments for printing.Wide compatibilityThe Creality SpacePi X4 filament dryer supports spools up to 200 mm in diameter and 150 mm in width with 1.75 mm and 2.85 mm diameter filaments. So you can dry both standard 1 kg spools and larger spools weighing 2 kg.Safe operationThe Creality SpacePi X4's triple protection system includes fan control, heater temperature protection and sensors that monitor the temperature in the chambers. This allows you to use the device without worrying about overheating or damaging the filaments.Everyday convenienceThe dryer is equipped with a chamber backlight, a sliding lock, anti-burn rollers and a moisture-proof seal to ensure comfort. In addition, the device signals the end of drying with a sound, making it easy to use.You control as you pleaseThe EDry UI panel allows you to precisely control drying parameters, including temperature, drying time (1-48 hours) and threshold humidity. You can use automatic modes or custom settings to tailor the drying process to the requirements of your specific filament.Included: Filament dryer Power cord User manual Manufacturer Creality Model SpacePi X4 Manufacturer code 4005010100 Rated power 360W Temperature range 45~85°C Drying time 1-48 h Input voltage 220-240V50/60Hz Supported filament Spool diameter: ≤200 mmWidth: ≤150 mmFilament diameter: 1.75 / 2.85 mm Dimensions 382 × 290 × 270 mm Weight 5 kg

Creality Ender-3 V3 3D PrinterCreality Ender-3 V3 is an advanced 3D printer that combines cutting-edge technology, stable design and intuitive interface to offer professionals and enthusiasts a tool for creating precise prints. With FDM (fused deposition modeling) technology, the printer provides high-quality prints in a variety of materials.Powerful printing functionsThe printer allows modeling in a variety of materials, such as PLA, TPU, PETG, ABS, PLA-CF, PETG-CF and CR-carbon, offering a wide range of design possibilities. It offers filament detection functions, which prevents interruption of the printing process. It takes place at speeds of up to 600 mm/s, and the coordinated movement of the X- and Z-axis is driven by two motors attached to the base, which increases the accuracy of the Z-axis and enables better quality prints. The printer supports the Gcode file format and allows printing from a USB drive, via LAN or from the cloud.Advanced designThe Ender-3 V3 features a new metal construction with die-cast parts for greater stability and durability. The gantry and base are made from a single piece of metal, further improving the accuracy of the Z-axis for better quality prints. The printer is also equipped with full-power direct extrusion, enabling clog-free extrusion for more than 1,000 hours. A 60-watt ceramic heater ensures full melting of filaments at high speed.Advanced coolingThe printer is equipped with a durable copper nozzle with a steel tip and titanium alloy heat shield. In addition, two powerful fans at the front and rear of the print head quickly and evenly cool the freshly printed section, ensuring excellent print quality even at high speeds.Easy operation and setupThe Ender-3 V3 offers automatic level detection and calibration, which prepares the printer for operation without the need for manual leveling. The printer is also equipped with a 4.3-inch HD color touchscreen that allows easy monitoring of the printing process, model previewing and temperature control with moving graphics. In addition, the printer features a Windows and Mac OS-compatible operating system, providing versatility in operation.Performance and precisionThe printer offers a maximum print speed of 600 mm/s and a maximum acceleration of 20000 mm/s^2, enabling fast and precise prints. The direct-driven extruder is reinforced with a helical spring and ball piston, ensuring strong filament gripping without slowing down. Extruder enhancements such as a side spring, ball piston and powder metallurgy lever further increase adhesion and extrusion force for precise printing.State-of-the-art printing featuresThe printer has an excellent software ecosystem that allows control and monitoring with Creality Print slicer and Creality Cloud APP. This system allows easy management and export of models. The spring steel base allows the model to be released with a slight bend, which is useful in the printing process. Manufacturer Creality Model Ender-3 V3 Modeling technology FDM Modeling dimensions 220 x 220 x 250 mm Leveling method automatic level detection Number of nozzles 1 pc. Extruder diameter 0.4 mm Layer thickness 0.1-0.35 mm Precision ±0.2 mm Nozzle temperature ≤ 300 Substrate temperature ≤ 110 Filaments PLA / TPU / PETG / ABS / PLA-CF / PETG-CF / CR-carbon Rated power 350 W Input voltage 100-120 V; 200-240 V; 50/60 Hz Filament detection Yes Lost power recovery Tak Printing method From USB disk / via LAN / from the cloud Print file format Gcode Clipping software Creality Print Operating system Windows / Mac OS Language Chinese, English, Spanish, German, French, Russian, Portuguese, Italian, etc.

Creality K1C 2025 3D PrinterThe Creality K1C is an advanced 3D printer that has been pre-assembled and calibrated at the factory - it takes just 3 minutes to start the first print. It has an enclosed work chamber measuring 220 × 220 × 250 mm, which provides a stable environment for working with more difficult filaments. A built-in extruder with an anti-clogging kit reduces the risk of failure. The whole thing runs under the powerful Creality OS operating system.Jam-free printing - new generation extruderThe K1C uses a robust extruder with an improved clamping mechanism that ensures stable filament feeding. This enables more than 1,000 hours of continuous printing without clogging. The interchangeable "Unicorn" nozzle, made of copper, steel and titanium, allows for quick replacement. It also blocks unwanted heating of the filaments at the top of the head, preventing material flow problems.Cooling on three levelsThe Creality K1C uses an advanced triple cooling system to take care of the quality of each print. The first fan at the head reduces heat creep by cooling the filament before it reaches the nozzle. The second is responsible for quickly curing the print immediately after layer application, improving adhesion between layers. The third fan, located in the chamber, takes care of even cooling of the entire model.Supports carbon fiber filamentsThe printer works well with technical materials such as PLA-CF or PET-CF, which are reinforced with carbon fiber. These filaments are used in the production of parts subjected to mechanical stress and elevated temperatures. K1C reaches up to 300°C, which allows it to work with filaments that are more difficult to process. The flexible PEI plate improves adhesion of the first layer and makes it easier to remove finished models.Automated and fastThe calibration process on the K1C comes down to a single click. The printer automatically aligns the table, sets the Z-axis and performs shape tests. The touchscreen interface resembles a smartphone screen in operation, making the device easy to use. The K1C achieves an impressive print speed of up to 600 mm/s while maintaining high quality. The maximum acceleration is as high as 20,000 mm/s², making it one of the fastest printers in its class. It owes this to its lightweight CoreXY design and rigid die-cast frame.Built-in AI cameraThe integrated AI camera actively monitors printing progress. It can detect phenomena such as so-called spaghetti, or tangled filament, or the presence of foreign objects on the table. If there is a problem, printing is automatically stopped and the user is notified. The camera is also suitable for remote viewing and creating impressive timelapse images of the printing process. This is a practical solution for those who want to have control over printing from anywhere.Thoughtful design and user comfortClosed chamber with transparent walls allows you to observe the printing process in real time. A built-in activated carbon filter reduces odors and cleans the air of particles emitted from hot filaments. The quiet mode allows the printer to operate with a volume not exceeding 45 dB. Every detail of the printer has been taken care of, from vibration-reducing shock absorbers to a reinforced cable guide. You'll also find a silicone strip for cleaning the nozzle, dampened hinges and an anti-splash film on the door. The printer also has room for a side spool holder and many ready-made accessories available as 3D models.Error handling and serial printingWhen one of the models in a batch print fails, the K1C allows you to simply skip it - without interrupting the entire batch. The feature is available in the Creality Print software and enables faster and more efficient management of large projects. The feature will also soon be available in Creality OS.Creality ecosystemThe Klipper-based Creality OS offers advanced features like vibration compensation and advanced filament flow control. You can modify it at will or join an active

Creality K2 Combo 3D PrinterThe Creality K2 Combo is a high-speed 3D printer with a CFS filament management system that allows printing up to 16 colors without manual filament changes. Its enclosed design, quiet operation (about 45 dB) and sturdy frame make it well suited for both home and workshop use. Print speed reaches 600 mm/s, and thanks to advanced stabilization, quality remains at a very high level.Multi-color printingThe K2 Combo was developed for creative multi-color and multi-material printing. The integrated CFS system automatically switches between filaments without any user intervention. It supports up to 4 CFS units, which means up to 16 different colors in a single print. The system is fully integrated with Creality OS and Creality Print software, making it easy to manage materials.Speed that goes hand in hand with qualityMaximum print speeds of up to 600 mm/sec and acceleration rates of up to 20,000 mm/sec² are thanks to the servo motion system. Thanks to its enclosed, rigid housing and stable guides, even at high speeds, details remain sharp and surfaces smooth. This is a good solution if you want fast prototyping without compromising on quality.Quiet operationThanks to the use of balanced fans and quiet servo motors, the printer operates with noise comparable to that of a laptop - about 45 dB. That's quiet enough to use it in a home office or studio without disrupting your daily routine.Smart features for user convenienceThe printer automatically levels the table, analyzing only the part on which the model will be placed. This reduces preparation time and increases the chance of a perfectly glued first layer. The system also detects printing errors, such as the formation of the so-called spaghetti effect, and informs the user.Design suitable for everyday useThe K2 Combo's chassis is made of aircraft-grade aluminum components, which translates into a durable and stable design. The working space of 260 × 260 × 260 mm allows you to create medium and larger models without the need to divide them into parts.Included 3D printer touchscreen spool holder filament PTFE tube power cord instruction manual nozzle cleaner cutting blade socket wrench imbus cutting pliers CFS system filament buffer Creality 485 cable (45 cm) Creality 485 cable (100 cm) quick start guide 3D printer Manufacturer Creality Model K2 Combo Printing technology FFF Print area 260 × 260 × 260 mm Device dimensions 404 × 436 × 545 mm Printing speed Up to 600 mm/sec Acceleration Up to 20,000 mm/s² Accuracy ±0.1 mm per 100 mm Extruder type Proximal two-speed extruder Filament diameter 1.75 mm Nozzle diameter 0.4 mm Max nozzle temperature Up to 300°C Max working table temperature Up to 100°C Working surface PEI spring steel construction plate Leveling method Automatic leveling Wireless connectivity Wi-Fi 2.4 GHz Built-in memory 8GB EMMC Rated power 1350 W/220 V, 450 W/110 V Voltage range 100-240 V~, 50/60 Hz Screen 4-inch color touch screen Supported filaments PLA, PETG, ABS, PLA-CF, PET Monitoring camera (AI) Standard configuration Resume after power loss Yes Air filter Yes Vibration optimization Yes Work chamber illumination Yes CFS system (automatic filament feeding) Yes CFS extension Up to 4 units Cutting software Creality Print 6.0 and later Supported languages Chinese, English, Spanish, German, French, Russian, Portuguese, Italian, Turkish, Japanese, Korean File transfer method USB drive / Wi-Fi Supported file formats G-code, 3MF CFS system Manufacturer Creality Product name CFS (Creality Filament System) Number of filament slots 4 Rated power 20 W Rated voltage DC 24 V Connectivity CFS: ≤4 Product dimensions 379 × 314 × 276 mm Weight 4.56 kg Status indicators 4 (one for each slot) Printing in multiple colors Supported Automatic filament switching Supported RFID tag reading Supported Filament end detection Supported Filament buffer Supported Moisture-resistant storage Yes, with moisture absorbers Compatible Films PLA, ABS, PETG, ASA, PET, PA-CF, P

Creality Ender-5 MaxThe Creality Ender-5 Max is a 3D printer designed for demanding users and professional projects. The solid, all-metal frame and 36-point automatic table leveling system guarantee excellent print quality from the first layer. Every detail of the model is precisely reproduced, and the print surface remains perfectly smooth. The consistency of layers and robustness of prints will satisfy even the most demanding customers.Unmatched print speed and workspaceThe Ender-5 Max impresses with its print speed, reaching up to 700 mm/s - a leading performance among CoreXY printers. Thanks to its precision design and advanced components, high-speed printing does not mean compromising on quality. Whether you're printing prototypes, technical details or decorative elements, every print is perfectly reproduced. With the device's impressive working space, you can realize larger projects without the need to divide them into parts - the Ender-5 Max allows you to print large models in one piece or mass produce smaller parts. It's ideal for professional workshops, manufacturing companies and 3D printing enthusiasts.Stability, versatility and precisionSolid cast aluminum construction and precision linear guides on the X-axis ensure smooth head movement without the slightest deviation. Two independent Z-axis motors, supported by pairs of leadscrews and linear guides, allow models weighing up to 10 kg to be lifted without problems. That's the end of problems with shifting layers or visible lines on the print surface. The ability to manage multiple printers via WLAN and tri-color status indicators that can be seen from up to 10 meters away make workflow easier. An optional enclosure allows the printer to maintain a higher ambient temperature, which is essential when printing with engineered filaments such as ABS or ASA.Ready to work in all conditionsThe printer operates stably at temperatures from 5 to 40°C, with no risk of clogging the print head, even during prolonged operation. The 1,000-watt heating table heats up quickly, allowing printing with a wide range of filaments, including PLA, PETG, PA, ABS and ASA. The Ender-5 Max supports input voltages from 100 to 240 V, eliminating the need to manually select settings. Thanks to its silent operation mode (noise level of less than 55 dB), the Ender-5 Max does not interfere with daily operations. Features of automatic filament loading and unloading, input resource sharing, 8 GB of ROM and Wi-Fi connectivity make printing simpler and more intuitive than ever before. Manufacturer Creality Model Ender-5 Max Printing technology Fused Deposition Modeling (FDM) Working volume 400 × 400 × 400 mm Printer dimensions 649 × 721 × 850 mm Printer weight ≤ 25.9 kg Printing speed ≤ 700 mm/s Acceleration ≤ 20,000 mm/s² Printing accuracy 100 ± 0.1 mm Layer height 0.05-0.3 mm Extruder Direct Drive Extruder Filament diameter 1.75 mm Nozzle diameter 0.4 mm (compatible with 0.6/0.8 mm nozzles) Nozzle temperature ≤ 300°C Working table temperature ≤ 100°C Working platform Flexible epoxy plate Leveling system Automatic leveling at 36 points Indicator lighting Red/Green/Yellow File transfer USB drive / Wi-Fi Screen Color touch screen 4.3 inches Camera Optional Recovery after power loss Yes Sensor for lack of filament Yes Input Shaping (signal shaping) Yes Lighting kit Yes Sleep mode Yes Rated voltage 100-240 V AC, 50/60 Hz Rated power 1250 W Operating temperature 5°C - 40°C Supported filaments Hyper PLA, PLA, PETG, TPU95A, ABS, ASA, PLA-CF, PA, PLA-Silk File format for printing G-Code Cutting software Creality Print 5.1 Cutting file formats STL, OBJ, 3MF Cloud printing application Creality Cloud User interface languages English, Spanish, German, French, Russian, Portuguese, Italian, Turkish, Japanese, Korean, Chinese

Creality K1 MAX 3D printerThe Creality K1 Max 3D printer is revolutionizing the 3D printing industry, offering printing speeds twelve times faster than standard FDM devices. Featuring innovative technologies such as the lightweight Core XY print head, Creality's intelligent operating system and advanced monitoring system, the K1 Max delivers performance, precision and ease of use. Discover innovative solutions to push the boundaries of traditional 3D printing.Agile and precise print headThe K1 Max combines agility and precision with a lightweight 190g print head, which guarantees less inertia of movement. This innovative design allows for faster and more accurate printing, eliminating vibration and increasing overall print quality. In addition, an improved Z-axis with precise positioning minimizes Z-banding, ensuring smooth and even layers.Advanced monitoring and LiDARThe K1 Max revolutionizes the printing process by using LiDAR with a resolution of 1 nanometer to scan the first layer and an AI camera to monitor the entire process. The device immediately reports errors such as spaghetti failure or the presence of foreign objects, allowing quick intervention. Spaghetti failure is a printing error resulting from the loss of adhesion of the printed object to its base - this results in clumped filament beams that resemble spaghetti. The device will alert you when the error occurs. The system allows you to monitor printing progress in real time and create time-lapse videos.Innovative heating and cooling technologyThe new K1 Max ceramic heater heats the filament to 200°C in just 40 seconds, and an additional 18W fan effectively improves cooling. Dual Cooling technology enables complex bridges and overhangs without the need for supports, allowing models to harden before warping occurs.Intelligent operating systemThe K1 Max uses Creality's intelligent operating system, which provides a simple user interface and synchronization of data and commands with various devices and the cloud. With a dual-core 1.2Hz processor and 8G ROM, the device supports high-speed printing and stores up to 400 models for efficient data writing and reading.Ease of use and reliabilityThe Creality K1 Max comes assembled and calibrated, greatly simplifying the process of getting started. Pressing a single button activates a self-test that checks all key components, including the extruder, heating table, camera, fan and leveling. Brand Creality Model K1 max Printing technology FDM Design volume 300 x 300 x 300 mm Product dimensions 435 x 462 x 526 mm Weight of the device 18kg Printing speed