Pla ABS

Creality SpacePi X4 Filament Dryer Box, 4-Spool Storage, Dual Heating Chambers, 85°C Max Temperature, for PLA/TPU/PETG/ABS/Nylon

Creality SpacePi X4 Filament DryerCreality SpacePi X4 is a powerful dual-chamber filament dryer, allowing you to dry as many as 4 spools simultaneously with full temperature control from 45 to 85°C. Thanks to the active drying technology, fast heating and quiet operation, you will prepare PLA, PETG, TPU, ABS or PA-CF filaments for printing in a reproducible and stable way, eliminating the problem of moisture, bubbles and shagging during printing.Dry a variety of filamentsThe device features two independently controlled heating chambers, allowing you to set different temperatures for different filaments (e.g. 50°C for PLA and 85°C for PA-CF). You can use one or both chambers as needed, which saves time and energy in a small workshop or when working with different materials at the same time.Speed and uniformityWith 200W + 200W PTC heaters, SpacePi X4 heats up to 85°C in about 20 minutes. The 360° air circulation ensures even heat distribution, and the SpaceDry 4.0 technology with active dehumidification and desiccant regeneration guarantees effective moisture removal without changing cartridges.Quiet, cheap, efficientThe Active Silent system keeps noise levels to just 43-46 dB, allowing you to work comfortably at home and in the workshop. The Creality SpacePi X4 offers energy-efficient operation with an energy consumption of 0.124 kWh in single-chamber mode and 0.208 kWh in dual-chamber mode, reducing the cost of preparing filaments for printing.Wide compatibilityThe Creality SpacePi X4 filament dryer supports spools up to 200 mm in diameter and 150 mm in width with 1.75 mm and 2.85 mm diameter filaments. So you can dry both standard 1 kg spools and larger spools weighing 2 kg.Safe operationThe Creality SpacePi X4's triple protection system includes fan control, heater temperature protection and sensors that monitor the temperature in the chambers. This allows you to use the device without worrying about overheating or damaging the filaments.Everyday convenienceThe dryer is equipped with a chamber backlight, a sliding lock, anti-burn rollers and a moisture-proof seal to ensure comfort. In addition, the device signals the end of drying with a sound, making it easy to use.You control as you pleaseThe EDry UI panel allows you to precisely control drying parameters, including temperature, drying time (1-48 hours) and threshold humidity. You can use automatic modes or custom settings to tailor the drying process to the requirements of your specific filament.Included: Filament dryer Power cord User manual Manufacturer Creality Model SpacePi X4 Manufacturer code 4005010100 Rated power 360W Temperature range 45~85°C Drying time 1-48 h Input voltage 220-240V50/60Hz Supported filament Spool diameter: ≤200 mmWidth: ≤150 mmFilament diameter: 1.75 / 2.85 mm Dimensions 382 × 290 × 270 mm Weight 5 kg

AnyCubic Kobra 2 Neo 3D PrinterThe AnyCubic Kobra 2 Neo 3D printer will allow you to print a wide variety of models quickly and accurately. It runs at a maximum speed of 250 mm/s and features a new integrated extruder. It also offers linear drive and input shaping to create detailed, high-quality prints. It also supports automatic leveling with Z-axis deviation compensation. At the same time, it is very simple and convenient to use.Impressive printing speedDon't want to wait too long for your models to be ready? The Kobra 2 Neo model will be perfect for you! The printer offers a maximum printing speed of up to 250 mm/s (with a recommended speed of 150 mm/s). To print 3DBenches with it, you only need about half an hour!New integrated extruderThe printer's improved extruder and cooling system enable fast filament dissolution with 60 watts of power. In turn, the built-in fan running at 7,000 rpm provides instant cooling and molding of the model. The Kobra 2 Neo is also distinguished by its compatibility with various types of filament, including PLA, TPU and PETG. This makes it great for a variety of applications!Detailed modelsThe printer also supports features such as line drive and input shaping, so the finished prints have better quality, stability, smoothness and richness of detail. Now even novice users can easily create stunning models!Automatic leveling systemThe Kobra 2 Neo supports the LeviQ 2.0 automatic leveling system, which additionally allows you to intelligently compensate for deviations in the Z-axis - it also allows you to level them using custom values. This means you can easily adapt it to your needs!Convenient operationTo operate the printer, there is a 2.4-inch LCD screen with a convenient dial. With its help, you can easily adjust settings, select the appropriate functions and much more. In addition, the entire device consists of 5 modules, making it very easy to assemble. Now you'll have the printer ready to go in no time and get busy creating high-quality models!Included Frame Base Screen with knob Filament holder Print head TF card (8 GB) Cable holder Card reader Nozzle Screw set Test filament Tool kit Power cable User manual Manufacturer AnyCubic Model KNVA0BK-Y-O Type FDM / FFF Structure Cartesian Filament detection Optional Leveling LeviQ 2.0 automatic system (25-point) Platform Magnetic PEI spring steel platform (220 x 220 mm) Y axis x1 rail Z axis Threaded rod Extruder Integrated, located directly above the printhead Cooling fan speed 7000 rpm X / Y axis ribbon tensioner Button for adjustment Control panel 2.4-inch LCD screen controlled by a rotary knob Data input MicroSD card Table temperature ≤ 110°C Dysza ≤ 260°C, Ø 0.4 mm (replaceable) Motherboard 32-bit Max. printing volume 12,1 l Compatible filament types PLA / TPU / ABS / PETG Printing speed Maximum: ≤ 250 mm/s; Standard: ≤ 150 mm/s; Max. printing dimensions 250 x 220 x 220 mm (W x S x G) Power supply 400 W Weight 7.3 kg Dimensions 485 x 440 x 440 mm

AnyCubic Kobra 2 Pro 3D PrinterLooking for a powerful, accurate and easy-to-use 3D printer? Opt for the Kobra 2 Pro model! Maximum printing speed of 500 mm/s and acceleration of up to 20,000 mm/s2 will allow you to create the models of your choice in no time, while automatic leveling, filament flow control and vibration compensation will ensure perfect results. Convenient operation of the printer is enabled by a built-in touch panel and a dedicated app.Maximum accelerationExperience how fast you can create your prints. The Kobra 2 Pro offers a standard print speed of 300 mm/sec and a top speed of up to 500 mm/sec. It also excels in acceleration up to 20,000 mm/s2. This will save you time! Relax and sip your favorite coffee while the printer prepares your model in no time.High-performance processorWhat makes the printer work so quickly and efficiently? The Kobra 2 Pro is equipped with a powerful 1.2 GHz Cortex-A7 processor, which guarantees powerful computing power. As a result, it can provide faster response times to commands, better engine control and impressive printing speeds.Optimized designThe printer's extruder is located directly above its print head, which, combined with SG15 bearings, a dual-shaft X / Y axis core and two Z axis guide screws, guarantees efficient and precise extrusion of the filament. It also allows it to dissolve and cool quickly, enabling smooth printing without visible layers.Top quality printingDo you care about the highest possible printing quality? Do you want your models to be detailed and realistic? With the Cobra 2 Pro printer, it becomes easier than ever before! The advanced compensation function reduces the effect of vibrations on the print quality, and the filament flow control mode allows you to adjust the amount of material to ensure even filling of layers.User-friendlyThe printer is equipped with a 4.3-inch color touchscreen for convenient operation. With its help you can easily adjust settings and much more! You also have a dedicated Anycubic app at your disposal, which allows you to check the device's status and update software remotely, among other things.Improved LeviQ 2.0 systemThe Kobra 2 Pro offers an enhanced LeviQ 2.0 system, which allows for automatic leveling and intelligent compensation of Z-axis deviation - and you can also level it using your own custom values. This makes it easy to adapt the printer to your current needs and situation!With an eye for detailThe printer's integrated design makes it easy to assemble and set up, and the magnetic spring-steel platform allows you to remove finished models without any problems. You can also adjust the tension of the X / Y axis bar with the appropriate knob. In addition, the 32-bit motherboard ensures smooth and precise printing, and up to 8 GB of built-in memory gives you the ability to store up to 400 model files. A filament break detection function is also available.Included Frame Base Touchscreen Filament holder Print head Filament detector Cable holder USB flash drive Nozzle Set of screws and caps Test filament Tool kit Power cable Lubricant User manual Manufacturer AnyCubic Model K2RC0BK-Y-O Type FDM / FFF Structure Cartesian Filament detection Default Leveling LeviQ 2.0 automatic system (25-point) Platform Magnetic PEI spring steel platform (220 x 220 mm) X / Y axes Dual metal spindles Z axis Double threaded rod Extruder Located directly above the print head + 2 gears Cooling fan speed 7000 rpm X / Y axis ribbon tensioner Yes Control panel 4.3-inch LCD touch screen Input ports 3x USB Table temperature ≤ 110°C Dysza ≤ 260°C, Ø 0.4 mm (replaceable) Motherboard 32-bit Max. printing volume 12,1 l Compatible filament types PLA / TPU / ABS / PETG Printing speed Maximum: ≤ 500 mm/s; Standard: ≤ 300 mm/s; Max. printing dimensions 250 x 220 x 220 mm (W x S x G) Power supply 400 W Weight 8.4 kg Dimensions 486 x 435 x 463 mm

Anycubic Kobra 3 V2 3D printerMeet the Anycubic Kobra 3 V2, a 3D printer that offers precise and fast printing. Its enhanced LeviQ 3.0 automatic leveling system with a 60 mm Y-axis and SG15 bearings guarantees perfect adhesion and flawless first layers, while speeds of up to 600 mm/s² and acceleration of 20,000 mm/s² reduce turnaround time for even the most demanding projects. Thanks to "plug & play", installation and initial startup take less than 15 minutes, while smart features such as resuming printing after power loss, filament detection and timelapse on the built-in 720 p camera ensure continuous and safe operation. The whole thing is complemented by the powerful Anycubic ecosystem, which gives you full control over every printing step.LeviQ 3.0 automatic levelingForget about tedious manual table calibration. The innovative LeviQ 3.0 system with a 60 mm Y-axis and SG15 bearings on the X-axis takes care of the perfect alignment of each layer. Thanks to the elimination of offsets in the Z-axis, you will get reliable adhesion of the first layer, which significantly increases the success rate of prints even on the most geometrically complex projects.Express speed and reliable performanceYou no longer have to wait long to print your designs. The Kobra 3 V2 achieves a maximum print speed of up to 600 mm/sec (300 mm/sec by default) and acceleration of up to 20,000 mm/sec², resulting in a small boat model in less than 13 minutes. The improved nozzle effectively minimizes filament leakage, and the optimal width of the working tunnel ensures comfort when working on any project.Unpack and runAssembling and starting the printer takes less time than your morning coffee - the intuitive, simplified design allows you to start your first print in a quarter of an hour after unpacking. Sturdy twin pull bolts, a precision bearing system and a metal quick-release coupler guarantee the stability of the entire design and allow for instant nozzle changes when needed.Smart monitoring and securityAnycubic Kobra 3 V2 has a filament sensor that detects its condition and automatically refills it. In addition, the printer resumes operation after a power outage or unexpected power loss. The built-in 720p timelapse camera allows you to document the entire process, which is great for order presentations or creating social media content.Full control in the Anycubic ecosystemWith Anycubic Slicer Next (based on the Orca engine), you'll prepare models for printing from the LAN, managing multiple projects simultaneously and skipping unwanted elements. Using Anycubic, you gain remote access to the printer, real-time progress monitoring and a time-lapse photography option. In addition, the Makeronline platform offers a rich library of pre-made models and one-click cutting and printing.Comprehensive feature setAnycubic Kobra 3 V2 is more than a printer. It's a tool that integrates top-notch automation and intelligent software. With a capacitive 4.3-inch touchscreen and control via panel, app and USB, you have complete freedom to choose how and where to work on your projects.Included Kobra 3 V2 printer print head touchscreen spool holder cable holder cleaning wiper screw M2x14 x2 screw M3x6 x4 screw M4x16 x2 screw M3x10 screw M3x8 power cord cable organizer x2 USB disk filament tube set of wrenches allen screws 4.0, 3.0, 2.5, 2.0, 1.5 sample of filament nozzle cleaner grease camera instruction manual Manufacturer Anycubic Model K3V2-IP-O Weight 9.37 kg Supported materials Kobra 3 V2 supports only PLA, TPU, PETG, ABS materials Dimensions 452.9 x 504.7 x 483 mm Power source 400 W Multicolor printing For multicolor printing, the ACE Pro is required Nozzle Maximum temperature 300℃ Print size 255 x 255 x 260 mm Maximum table temperature 110℃ Maximum print speed 600 mm/sec Touch screen 4.3-inch Active drying ACE Pro required Auto leveling mode LeviQ3.0 + no Z-axis offset + design optimization Nozzle diameter Standard 0.4mm, options: 0.25/0.6/0.8mm Filament detection a

Elegoo Centauri Carbon 3D Printer, CoreXY 500mm/s High-Speed, 320°C Nozzle, Carbon Fiber/PLA/ABS Compatible, LED Strip, 256*256*256mm

Creality CFS multi-filament systemCreality CFS is an advanced multi-filament system that allows 3D printing in as many as 4 colors simultaneously (expandable to 16 colors), eliminating the need to paint models afterwards. Thanks to intelligent features such as automatic filament identification, smooth spool changes and abnormality detection, the printing process is seamless. An airtight design with moisture absorbers protects the filament from humidity, and an easy-to-read display allows you to monitor storage conditions in real time. Compatibility with Creality Hyper Series cardboard spools and practical solutions like the spring-loaded batten bar mechanism make the CFS an indispensable tool for any 3D creator.Intelligent print support and automationCreality CFS allows printing with support materials that can be easily removed - either mechanically or by dissolving in water. This keeps the final model free of support marks, significantly improving the aesthetics and precision of the prints. Equipped with advanced sensors, the CFS system automatically detects any irregularities during printing. If a problem is detected, it immediately stops the job and informs the user, eliminating the risk of damaging the project. The function of automatic identification of the filament with RFID tags allows immediate recognition of the type, color and properties of the material, and for standard filaments, the information can be entered manually.Smooth operation without downtimeThe CFS system intelligently manages filament changes during multicolor printing. When a spool runs out, the device automatically switches to the next appropriate filament, minimizing waste and eliminating downtime. The automatic filament mapping function ensures full synchronization with Creality 3D printers and Creality Print software, making the printing process seamless.Thoughtful designThe airtight design of the CFS, supported by special moisture absorbers, effectively protects the filament from absorbing moisture from the air. A built-in temperature and humidity display allows ongoing monitoring of storage conditions, and the system alerts the user if the optimum humidity level is exceeded. A spring-loaded batten bar mechanism prevents the filament from popping out of the slot during printing, and compatibility with Creality Hyper Series cardboard spools means you can take advantage of eco-friendly solutions without additional adapters. Manufacturer Creality Product name CFS (Creality Filament System) Number of filament slots 4 Rated power 20 W Rated voltage DC 24 V Connectivity CFS: ≤4 Product dimensions 379 × 314 × 276 mm Weight 4.56 kg Status indicators 4 (one for each slot) Printing in multiple colors Supported Automatic filament switching Supported RFID tag reading Supported End of Filament Detection Supported Filament buffer Supported Moisture-resistant storage Yes, with moisture absorbers Compatible Films PLA, ABS, PETG, ASA, PET, PA-CF, PLA-CF (incompatible with moisture resistant filaments, TPU95A and other flexible materials) Filament diameter 1.75 ± 0.05 mm Spool requirements A 1 kg spool or any spool with a diameter of 197-202 mm and a width of 42-68 mm

Creality Ender-3 V3 3D PrinterCreality Ender-3 V3 is an advanced 3D printer that combines cutting-edge technology, stable design and intuitive interface to offer professionals and enthusiasts a tool for creating precise prints. With FDM (fused deposition modeling) technology, the printer provides high-quality prints in a variety of materials.Powerful printing functionsThe printer allows modeling in a variety of materials, such as PLA, TPU, PETG, ABS, PLA-CF, PETG-CF and CR-carbon, offering a wide range of design possibilities. It offers filament detection functions, which prevents interruption of the printing process. It takes place at speeds of up to 600 mm/s, and the coordinated movement of the X- and Z-axis is driven by two motors attached to the base, which increases the accuracy of the Z-axis and enables better quality prints. The printer supports the Gcode file format and allows printing from a USB drive, via LAN or from the cloud.Advanced designThe Ender-3 V3 features a new metal construction with die-cast parts for greater stability and durability. The gantry and base are made from a single piece of metal, further improving the accuracy of the Z-axis for better quality prints. The printer is also equipped with full-power direct extrusion, enabling clog-free extrusion for more than 1,000 hours. A 60-watt ceramic heater ensures full melting of filaments at high speed.Advanced coolingThe printer is equipped with a durable copper nozzle with a steel tip and titanium alloy heat shield. In addition, two powerful fans at the front and rear of the print head quickly and evenly cool the freshly printed section, ensuring excellent print quality even at high speeds.Easy operation and setupThe Ender-3 V3 offers automatic level detection and calibration, which prepares the printer for operation without the need for manual leveling. The printer is also equipped with a 4.3-inch HD color touchscreen that allows easy monitoring of the printing process, model previewing and temperature control with moving graphics. In addition, the printer features a Windows and Mac OS-compatible operating system, providing versatility in operation.Performance and precisionThe printer offers a maximum print speed of 600 mm/s and a maximum acceleration of 20000 mm/s^2, enabling fast and precise prints. The direct-driven extruder is reinforced with a helical spring and ball piston, ensuring strong filament gripping without slowing down. Extruder enhancements such as a side spring, ball piston and powder metallurgy lever further increase adhesion and extrusion force for precise printing.State-of-the-art printing featuresThe printer has an excellent software ecosystem that allows control and monitoring with Creality Print slicer and Creality Cloud APP. This system allows easy management and export of models. The spring steel base allows the model to be released with a slight bend, which is useful in the printing process. Manufacturer Creality Model Ender-3 V3 Modeling technology FDM Modeling dimensions 220 x 220 x 250 mm Leveling method automatic level detection Number of nozzles 1 pc. Extruder diameter 0.4 mm Layer thickness 0.1-0.35 mm Precision ±0.2 mm Nozzle temperature ≤ 300 Substrate temperature ≤ 110 Filaments PLA / TPU / PETG / ABS / PLA-CF / PETG-CF / CR-carbon Rated power 350 W Input voltage 100-120 V; 200-240 V; 50/60 Hz Filament detection Yes Lost power recovery Tak Printing method From USB disk / via LAN / from the cloud Print file format Gcode Clipping software Creality Print Operating system Windows / Mac OS Language Chinese, English, Spanish, German, French, Russian, Portuguese, Italian, etc.

AnyCubic Kobra 3 Combo 3D Printer K3CBBK0A-O