ABS 1.75

Number of Hoses: 4

Number of Hoses: 4

Number of Hoses: 6

Number of Hoses: 6

Sunlu S4 Filament DryerThe SUNLU FilaDryer S4 is an advanced filament dryer designed for demanding 3D printing users. It offers a massive capacity—drying up to 4 spools (1 kg each) simultaneously—and the ability to work with multiple printers at once. With a power output of 320–330 W, rapid heating (up to 50°C in just 30 minutes), and a maximum temperature of 70°C, the device ensures effective and uniform drying of even the most demanding materials, such as PA or PC. The built-in humidity control system, touchscreen, 8 filament outputs, and predefined material profiles make using the device not only effective but also extremely convenient.Dry up to 4 filaments simultaneously – maximum productivityThanks to the large chamber (450 × 210 × 211 mm), you can dry up to four spools of filament at the same time. This is the perfect solution for multicolor printing or working with multiple printers simultaneously. You don’t waste time changing materials—everything is ready in one place, which significantly speeds up and streamlines the entire process.Instant heating and high power – efficiency that makes a differencePerformance is ensured by a PTC heater with a power of up to 330 W, which allows it to reach 50°C in about 30 minutes and a maximum of 70°C. This means shorter filament preparation time and greater drying efficiency. Even difficult, hygroscopic materials regain their properties faster than ever before.Ideal temperature balance – perfect drying for every spoolA three-fan system (on the sides and bottom) ensures even air circulation and temperature stability within ±3°C. This ensures that every section of the filament is dried evenly, resulting in better print quality, greater consistency, and no surprises during operation.Smart humidity control – filament always in perfect conditionAn advanced humidity control system automatically starts drying when the humidity level exceeds the set range (30–50%) and stops the process once optimal conditions are reached (approx. 25%). This means full automation and the assurance that the filament is always ready for use—without manual monitoring.Safety and ease of use – technology you can rely onThe SUNLU S4 is equipped with a triple safety system: a PTC heater, a temperature sensor, and software protection. The device monitors temperature in real time and alerts you to any abnormalities, ensuring safe operation. Additionally, the touchscreen and pre-set profiles for PLA, ABS, PETG, TPU, PA, and PC simplify operation and eliminate the guesswork involved in settings.Full compatibility and flexibility – tailor the equipment to your needsSupport for filaments with diameters of 1.75 mm, 2.85 mm, and 3.00 mm, along with compatibility with most 3D printers, ensures the SUNLU S4 performs well in any environment. Eight filament outputs and the ability to connect multiple printers simultaneously allow for flexible workstation configuration. This device truly expands your capabilities and lets you create without limits.Included: SUNLU S4 Filament Dryer Power cord PTFE tubes User manual Manufacturer Sunlu Model Fila Dryer S4 Rated power 320–330 W Power supply AC 100–240 V / 50–60 Hz Maximum temperature 70°C Heating time to 50°C approx. 30 minutes Capacity 4 spools (1 kg each) Internal dimensions 450 × 210 × 211 mm Device dimensions 516 × 278 × 350 mm Net weight 4.8 kg Gross weight 5.5 kg Heating system PTC + 3 fans Temperature stability ±3°C Humidity control Automatic (start 30–50%, stop approx. 25%) Supported materials PLA, ABS, PETG, TPU, PA, PC Supported filament diameters 1.75 mm / 2.85 mm / 3.00 mm Number of filament outlets 8 (can be used with PTFE tubes) Display Touchscreen LCD

CREALITY SpacePi X4L Filament Dryer3D printing requires properly prepared filament. Even a small amount of moisture can compromise print quality, cause air bubbles, or result in poor layer adhesion. The Creality SpacePi X4L Filament Dryer is designed to keep the material in optimal conditions before and during printing. The device uses smart sensors, temperature control, and an intuitive touchscreen panel, making filament drying simple and precise.Smart Temperature and Humidity SensorsThe SpacePi X4L uses advanced sensors to monitor temperature and humidity inside the chamber. This allows the device to respond to even slight changes in parameters and maintain stable drying conditions. In practice, this means more uniform filament preparation, which translates to a more stable material flow during printing and better model quality.LCD touchscreen with operation controlThe device is operated via a clear LCD touchscreen. The new display design with an anti-static coating ensures good visibility even in cooler conditions. The panel allows you to quickly set the drying time and temperature, and the automatic mode selects the appropriate parameters on its own. You can also check the humidity level inside the device in real time on the screen.Double insulation for safetyThe dryer’s housing is equipped with a double layer of insulation that retains heat inside the chamber. The drying temperature can reach up to 75°C, yet the outer part of the housing remains significantly cooler—around 60°C. This allows the device to be safely operated even while in use.Wide filament compatibilityThe Creality SpacePi X4L supports most popular filaments used in 3D printing. The device is compatible with 1 kg or 2 kg spools and filaments with diameters of 1.75 mm and 2.85 mm. The chamber accommodates spools with a diameter of up to 200 mm and a width of up to 150 mm, making it compatible with many materials used in 3D printers.Precise time and temperature controlThe dryer allows you to set the temperature between 45 and 75°C and the operating time from 1 to 48 hours. This allows you to tailor the drying process to specific materials, such as PLA, PETG, TPU, or other filaments that require moisture removal before printing. Manufacturer Creality Model SpacePi X4L Product dimensions 382 × 290 × 270 mm Weight 5 kg Housing material ABS / PA / PC Operating temperature range 45–75°C Drying time 1 to 48 hours Rated power 340 W Input voltage 220–240 V ~ 50/60 Hz (UK / EU / AU / BR / CL / AR), 100–120 V ~ 50/60 Hz (US / JP) Filament diameter 1.75 mm / 2.85 mm Maximum spool diameter 200 mm Maximum spool width 150 mm

Anycubic ACE 2 Pro Multi-Filament System for the Kobra S1The Anycubic ACE 2 Pro is an advanced multi-filament system that opens up new possibilities in 3D printing, allowing you to create models in up to 16 colors. It supports 4 colors as standard, but connecting four units allows you to significantly expand the color palette and tackle more complex projects. The system is compatible with Anycubic printers such as the Kobra 3, Kobra 3 V2, Kobra 3 Max, Kobra S1, Kobra S1 Max, and Kobra X, offering great flexibility in adapting to your existing equipment.Smooth and fast filament feedingThe device uses 4 independent brushless motors that ensure stable, quiet, and precise operation. A new-generation buffering mechanism ensures smooth filament feeding and retraction, eliminating the risk of jams in each channel. Loading speed has been increased to 50 mm/s, a 100% improvement over the previous version, and filament change time has been reduced to approximately 56 seconds, saving up to 47 minutes over 100 changes.Optimal conditions thanks to drying and humidity controlThe ACE 2 Pro system allows for simultaneous filament drying and printing, keeping the material in optimal condition throughout the entire operation. Built-in temperature and humidity sensors monitor conditions in real time, and a solenoid valve actively removes excess moisture. An additional silicone ring seal protects the filament from external factors, resulting in better print quality and a lower risk of errors.Durable construction and quiet operationThe input ports, made of alumina ceramic, are highly wear-resistant, which extends the device’s lifespan and reduces the need for maintenance. Brushless motors offer a lifespan of at least 5,000 operating hours. At the same time, the device operates very quietly—below 48 dB with the door closed, and around 55 dB during active drying—allowing for comfortable use even in enclosed spaces.Easy maintenance and quick jam removalThe use of external feed channels and a quick-release mechanism allows for instant disassembly and removal of any jams. As a result, servicing takes only a few seconds and requires no complicated tools, significantly enhancing user convenience.Smart printing assistanceThe built-in smart assistant system offers features that genuinely simplify daily work. The device estimates the amount of filament remaining on the spool, automatically switches to a new spool when it runs out, and recognizes Anycubic filaments and their parameters (when connected to the internet). This makes the printing process more predictable and maintenance-free. Manufacturer Anycubic Model Ace 2 Pro Product code DS20-IP-O Dimensions 368 × 291.5 × 236.5 mm Weight 3.7 kg Enclosure material ABS/PC Motors 4 × brushless motors Filament compatibility PLA, PETG, ABS, ASA, PET, PA, PC, PVA (dry), BVOH (dry), PP, POM, HIPS, PLA-CF, PETG-CF, PAHT-CF, TPU (for ACE), PVB Filament diameter 1.75 mm Spool compatibility Spool outer diameter: 195–200 mmSpool width: 60–68 mmSpool thickness: 3–6 mm Smart filament identification Supported Filament end detection Supported Automatic print resume Supported Maximum drying temperature 65°C Drying efficiency Suitable for: PLA, PETG, PVB, TPUCompatible but not optimized: ASA, ABS, PET, PA, PC, PP, BVOH, POM, HIPS, fiber-reinforced materials Active humidity control Supported Sealed chamber Supported External PTFE tube Supported Temperature and humidity monitoring Temperature and humidity levels (visible in the app, slicer, and on the printer screen) Rated power 220 V: 330 W (max.)110 V: 235 W (max.) Printer compatibility Kobra 3 / Kobra 3 V2 / Kobra 3 Max / Kobra S1 / Kobra S1 Max / Kobra X

Creality Ender-5 MaxThe Creality Ender-5 Max is a 3D printer designed for demanding users and professional projects. The solid, all-metal frame and 36-point automatic table leveling system guarantee excellent print quality from the first layer. Every detail of the model is precisely reproduced, and the print surface remains perfectly smooth. The consistency of layers and robustness of prints will satisfy even the most demanding customers.Unmatched print speed and workspaceThe Ender-5 Max impresses with its print speed, reaching up to 700 mm/s - a leading performance among CoreXY printers. Thanks to its precision design and advanced components, high-speed printing does not mean compromising on quality. Whether you're printing prototypes, technical details or decorative elements, every print is perfectly reproduced. With the device's impressive working space, you can realize larger projects without the need to divide them into parts - the Ender-5 Max allows you to print large models in one piece or mass produce smaller parts. It's ideal for professional workshops, manufacturing companies and 3D printing enthusiasts.Stability, versatility and precisionSolid cast aluminum construction and precision linear guides on the X-axis ensure smooth head movement without the slightest deviation. Two independent Z-axis motors, supported by pairs of leadscrews and linear guides, allow models weighing up to 10 kg to be lifted without problems. That's the end of problems with shifting layers or visible lines on the print surface. The ability to manage multiple printers via WLAN and tri-color status indicators that can be seen from up to 10 meters away make workflow easier. An optional enclosure allows the printer to maintain a higher ambient temperature, which is essential when printing with engineered filaments such as ABS or ASA.Ready to work in all conditionsThe printer operates stably at temperatures from 5 to 40°C, with no risk of clogging the print head, even during prolonged operation. The 1,000-watt heating table heats up quickly, allowing printing with a wide range of filaments, including PLA, PETG, PA, ABS and ASA. The Ender-5 Max supports input voltages from 100 to 240 V, eliminating the need to manually select settings. Thanks to its silent operation mode (noise level of less than 55 dB), the Ender-5 Max does not interfere with daily operations. Features of automatic filament loading and unloading, input resource sharing, 8 GB of ROM and Wi-Fi connectivity make printing simpler and more intuitive than ever before. Manufacturer Creality Model Ender-5 Max Printing technology Fused Deposition Modeling (FDM) Working volume 400 × 400 × 400 mm Printer dimensions 649 × 721 × 850 mm Printer weight ≤ 25.9 kg Printing speed ≤ 700 mm/s Acceleration ≤ 20,000 mm/s² Printing accuracy 100 ± 0.1 mm Layer height 0.05-0.3 mm Extruder Direct Drive Extruder Filament diameter 1.75 mm Nozzle diameter 0.4 mm (compatible with 0.6/0.8 mm nozzles) Nozzle temperature ≤ 300°C Working table temperature ≤ 100°C Working platform Flexible epoxy plate Leveling system Automatic leveling at 36 points Indicator lighting Red/Green/Yellow File transfer USB drive / Wi-Fi Screen Color touch screen 4.3 inches Camera Optional Recovery after power loss Yes Sensor for lack of filament Yes Input Shaping (signal shaping) Yes Lighting kit Yes Sleep mode Yes Rated voltage 100-240 V AC, 50/60 Hz Rated power 1250 W Operating temperature 5°C - 40°C Supported filaments Hyper PLA, PLA, PETG, TPU95A, ABS, ASA, PLA-CF, PA, PLA-Silk File format for printing G-Code Cutting software Creality Print 5.1 Cutting file formats STL, OBJ, 3MF Cloud printing application Creality Cloud User interface languages English, Spanish, German, French, Russian, Portuguese, Italian, Turkish, Japanese, Korean, Chinese

Dualtron Mini 52V 17,5 ah elektriskais skrejriteni, 52V 500W elektriskais skrejritenis Dualtron Mini ir Dualtron augstas kvalitātes elektrisko skrejriteņu modelis. Mini ir kompakts pēc saviem izmēriem, ērts ar 8,5 collu riepām un viegli kopjams. Tam ir disku bremzes + elektriskās bremzes, kas ļauj skrejritenim apstāties vienmērīgi un bez stresa. Nenovērtējiet par zemu Minis tā izmēra dēļ, šis elektriskajais skrejritenis ar savu jaudīgo MAX 1450 W BLDC motoru un  52 V 17,5 AH LG akumulatoru spēj nobraukt līdz 55* km ar vienu baterijas pilno uzlādi! Mini ir patiesi iespaidīgs! Baterija: 52V 17,8 Ah Maks. attālums līdz (km) 55* km Motora jauda (W): 500 W Svars: 22 kg Maksimāli pieļaujamā slodze: 100 kg Bremzes: Disku bremzes + magnētiskās aizmugurējās Amortizācija: Priekšējā un aizmugurējā SpringR tehnoloģija Riteņi: pneimatiskie 8.5 collas ar kameru Izmēri: 96 x 21 x 39 cm Izmēri saliktā veidā: 115 x 53 x 106 cm Drošs salikšanas mehānisms Jaunā Dualtron Mini salikšanas sistēma neapšaubāmi ir viena no izturīgākajām un stabilākajām salikšanas sistēmām tirgū. Dualtron Mini ir ātri saliekamsun sniedz jums nepieciešamo pārliecību gan braucot, gan transportējot elektrisko skrejriteni.   Droša bremžu sistēma un ABS Ar uzticamām un viegli kopjamām disku bremzēm un elektriskajām bremzēm jūs varat būt pārliecināti, ka vienmēr saņemsiet paredzēto bremzēšanas jaudu, neuztraucoties par bremžu regulēšanu. Lai palielinātu izturību, elektriskās bremzes palīdz arī aizsargāt pret ekstremālām situācijām ar priekšlaicīgu mehānisko bremžu bloķēšanu. Reģeneratīvās uzlādes iespēja ir pozitīva arī akumulatora jaudai, kā arī var palīdzēt saglabāt bremzes, pateicoties pievienotajai pretestībai. Bremžu pretbloķēšanas sistēma (ABS) Dualtron Mini palīdzēs novērst riepu bloķēšanu bremzēšanas laikā.   3.paaudzes gismas sistēma Dualtron Mini 3. paaudzes gaismas sistēma galvenokārt ir paredzēta, lai uzlabotu drošību un paredzamību straujā pilsētas vidē. Dubultais LED priekšējais lukturis, stūres caurulē un sānu paneļa lukturi, kā arī bremžu gaismas aizmugurē nodrošinās jums un jūsu cilvēkiem jums blakus nepieciešamo redzamību un drošību pilsētvidē, īpaši tumšajā laikā. *maksimālais nobraukums tiek mērīts braucot ideālajos apstākļos: — bezvējā; — pa taisno ceļu bez kāpumiem; — braucēja svars līdz 60 kg; — EKO braukšanas režīmā (vidējais ātrums 15 km/st); — vides temperatūra +25 °C grādi. Atceries — reālais nobraukums var atšķirties!