Pla 2.85 mm

Sunlu S4 Filament DryerThe SUNLU FilaDryer S4 is an advanced filament dryer designed for demanding 3D printing users. It offers a massive capacity—drying up to 4 spools (1 kg each) simultaneously—and the ability to work with multiple printers at once. With a power output of 320–330 W, rapid heating (up to 50°C in just 30 minutes), and a maximum temperature of 70°C, the device ensures effective and uniform drying of even the most demanding materials, such as PA or PC. The built-in humidity control system, touchscreen, 8 filament outputs, and predefined material profiles make using the device not only effective but also extremely convenient.Dry up to 4 filaments simultaneously – maximum productivityThanks to the large chamber (450 × 210 × 211 mm), you can dry up to four spools of filament at the same time. This is the perfect solution for multicolor printing or working with multiple printers simultaneously. You don’t waste time changing materials—everything is ready in one place, which significantly speeds up and streamlines the entire process.Instant heating and high power – efficiency that makes a differencePerformance is ensured by a PTC heater with a power of up to 330 W, which allows it to reach 50°C in about 30 minutes and a maximum of 70°C. This means shorter filament preparation time and greater drying efficiency. Even difficult, hygroscopic materials regain their properties faster than ever before.Ideal temperature balance – perfect drying for every spoolA three-fan system (on the sides and bottom) ensures even air circulation and temperature stability within ±3°C. This ensures that every section of the filament is dried evenly, resulting in better print quality, greater consistency, and no surprises during operation.Smart humidity control – filament always in perfect conditionAn advanced humidity control system automatically starts drying when the humidity level exceeds the set range (30–50%) and stops the process once optimal conditions are reached (approx. 25%). This means full automation and the assurance that the filament is always ready for use—without manual monitoring.Safety and ease of use – technology you can rely onThe SUNLU S4 is equipped with a triple safety system: a PTC heater, a temperature sensor, and software protection. The device monitors temperature in real time and alerts you to any abnormalities, ensuring safe operation. Additionally, the touchscreen and pre-set profiles for PLA, ABS, PETG, TPU, PA, and PC simplify operation and eliminate the guesswork involved in settings.Full compatibility and flexibility – tailor the equipment to your needsSupport for filaments with diameters of 1.75 mm, 2.85 mm, and 3.00 mm, along with compatibility with most 3D printers, ensures the SUNLU S4 performs well in any environment. Eight filament outputs and the ability to connect multiple printers simultaneously allow for flexible workstation configuration. This device truly expands your capabilities and lets you create without limits.Included: SUNLU S4 Filament Dryer Power cord PTFE tubes User manual Manufacturer Sunlu Model Fila Dryer S4 Rated power 320–330 W Power supply AC 100–240 V / 50–60 Hz Maximum temperature 70°C Heating time to 50°C approx. 30 minutes Capacity 4 spools (1 kg each) Internal dimensions 450 × 210 × 211 mm Device dimensions 516 × 278 × 350 mm Net weight 4.8 kg Gross weight 5.5 kg Heating system PTC + 3 fans Temperature stability ±3°C Humidity control Automatic (start 30–50%, stop approx. 25%) Supported materials PLA, ABS, PETG, TPU, PA, PC Supported filament diameters 1.75 mm / 2.85 mm / 3.00 mm Number of filament outlets 8 (can be used with PTFE tubes) Display Touchscreen LCD

CREALITY SpacePi X4L Filament Dryer3D printing requires properly prepared filament. Even a small amount of moisture can compromise print quality, cause air bubbles, or result in poor layer adhesion. The Creality SpacePi X4L Filament Dryer is designed to keep the material in optimal conditions before and during printing. The device uses smart sensors, temperature control, and an intuitive touchscreen panel, making filament drying simple and precise.Smart Temperature and Humidity SensorsThe SpacePi X4L uses advanced sensors to monitor temperature and humidity inside the chamber. This allows the device to respond to even slight changes in parameters and maintain stable drying conditions. In practice, this means more uniform filament preparation, which translates to a more stable material flow during printing and better model quality.LCD touchscreen with operation controlThe device is operated via a clear LCD touchscreen. The new display design with an anti-static coating ensures good visibility even in cooler conditions. The panel allows you to quickly set the drying time and temperature, and the automatic mode selects the appropriate parameters on its own. You can also check the humidity level inside the device in real time on the screen.Double insulation for safetyThe dryer’s housing is equipped with a double layer of insulation that retains heat inside the chamber. The drying temperature can reach up to 75°C, yet the outer part of the housing remains significantly cooler—around 60°C. This allows the device to be safely operated even while in use.Wide filament compatibilityThe Creality SpacePi X4L supports most popular filaments used in 3D printing. The device is compatible with 1 kg or 2 kg spools and filaments with diameters of 1.75 mm and 2.85 mm. The chamber accommodates spools with a diameter of up to 200 mm and a width of up to 150 mm, making it compatible with many materials used in 3D printers.Precise time and temperature controlThe dryer allows you to set the temperature between 45 and 75°C and the operating time from 1 to 48 hours. This allows you to tailor the drying process to specific materials, such as PLA, PETG, TPU, or other filaments that require moisture removal before printing. Manufacturer Creality Model SpacePi X4L Product dimensions 382 × 290 × 270 mm Weight 5 kg Housing material ABS / PA / PC Operating temperature range 45–75°C Drying time 1 to 48 hours Rated power 340 W Input voltage 220–240 V ~ 50/60 Hz (UK / EU / AU / BR / CL / AR), 100–120 V ~ 50/60 Hz (US / JP) Filament diameter 1.75 mm / 2.85 mm Maximum spool diameter 200 mm Maximum spool width 150 mm

Sunlu E2 Filament DryerThe SUNLU FilaDryer E2 is a groundbreaking 2-in-1 device designed for the most demanding 3D printing users—it combines drying and annealing functions, offering full control over material properties. With a power output of 500W, rapid heating (50°C in 20 minutes, 70°C in 30 minutes), and a maximum temperature of 110°C, the E2 not only dries the filament but also significantly improves its mechanical properties. Its sealed design, large chamber accommodating spools up to 3 kg, and intelligent safety features make it a professional tool for working with both engineering and standard materials.Drying and annealing in one—maximum quality for your printsThe SUNLU E2 not only removes moisture from filaments but also allows for their annealing, a process that significantly increases the impact resistance, strength, and stability of your models. This solution will be particularly appreciated by those working with engineering materials—your prints become stronger, more durable, and ready for the most demanding applications.Up to 110°C – full power for engineering materialsThanks to its high operating temperature, the device supports as much as 99.99% of filaments available on the market, including advanced materials such as PA, PC, ASA, and composites with carbon and glass fibers. This means you can work without limitations—whether you’re creating mechanical parts, drone components, or parts requiring high durability.Instant heating – time savings and greater efficiencyA powerful 500W PTC heater ensures the device heats up extremely quickly. You don’t waste time waiting – the filament is ready to use almost immediately. This is particularly important for intensive projects and production work, where every minute counts.Fully sealed and insulated – filament always dry and readyAn advanced sealing system with silicone components effectively blocks moisture from entering from the outside. Additionally, the dual-chamber design provides excellent thermal insulation, allowing for a stable temperature to be maintained even above 100°C. The result? Ideal conditions for both drying and annealing—without the risk of re-moisturization.Large workspace – more possibilities in a single deviceThe chamber, sized to accommodate large spools (up to Ø250 mm), allows for various configurations—from two 1 kg spools, through 2 kg, up to a single 3 kg spool. This is a huge convenience for those working on larger projects or using industrial filaments.Smart safety features – safety without compromiseThe SUNLU E2 is equipped with a multi-level protection system: temperature control, automatic shutdown in case of overheating, and warning alarms. Additionally, double insulation ensures that even at internal temperatures above 100°C, the housing remains safe to touch. This is equipment you can rely on.Unlimited compatibility – one device for everythingSupport for 1.75 mm and 2.85 mm filament diameters and compatibility with a wide range of materials—from PLA to advanced composites—mean the E2 fits into any workspace. Built-in material profiles and simple operation let you quickly select optimal settings and focus on what matters most—creating.Annealing that makes a difference – unlock the potential of your materialsThe annealing process reduces internal stresses created during printing and significantly improves the mechanical properties of your models. With the SUNLU E2, your prints gain a new level of quality—greater strength, stability, and durability—opening the door to professional and industrial applications.Included: SUNLU E2 Filament Dryer PTFE tubes Annealing tray Power cord High-temperature resistant gloves User manual Manufacturer Sunlu Model Fila Dryer E2 Maximum operating temperature 110°C Power 500 W Power supply AC 100–240 V / 50–60 Hz Heating time to 50°C approx. 20 minutes Heating time to 70°C approx. 30 minutes Supported filament diameters 1.75 mm / 2.85 mm Maximum spool size Ø250 × 153 mm Capacity 2 × 1 kg / 2 × 2 kg / 1 ×

Creality SparkX i7 Combo 3D PrinterThe Creality SparkX i7 Combo 3D Printer is a state-of-the-art device designed for users who want to print quickly, accurately, and without unnecessary setup. The model uses Fused Filament Fabrication (FFF) technology and combines high print speeds with automation systems that simplify daily operations. The kit also includes the CFS Lite module, which enables multicolor printing and convenient filament management.High print speedThe Creality SparkX i7 was designed with rapid model creation in mind. A maximum print speed of up to 500 mm/s and acceleration of up to 10,000 mm/s² significantly reduce project completion time. In practice, this means faster prototyping and the ability to print more parts in less time. The use of Input Shaping and Pressure Advance stabilizes the print head’s movement during operation, ensuring that even at high speeds, the model’s surface quality remains high.Automatic setup and user-friendly operationThe printer features fully automatic bed leveling, eliminating the need for manual calibration. This makes getting started easier and faster, especially for those just beginning their journey with 3D printing. Control is handled via a 2.85-inch color touchscreen, which provides quick access to the printer’s most important functions. The device also supports file transfer via Wi-Fi or USB drive, allowing you to conveniently prepare prints from your computer.AI camera and print monitoring systemThe SparkX i7 features a 720p AI camera with lighting that allows you to monitor the printer’s operation. The camera analyzes the printing process and detects common errors, such as “spaghetti”—the uncontrolled formation of filament strands. The system also monitors for filament shortages, tangled material, or printing in mid-air. This allows the device to stop printing and prevent waste of material and time.Interchangeable hotend and wide filament compatibilityThe printer is equipped with a quick-change hotend that can be swapped without tools. This solution simplifies maintenance and allows for faster configuration adjustments for different projects. The standard 0.4 mm nozzle can be replaced with 0.2 / 0.6 / 0.8 mm nozzles, allowing the user to adapt the printer for precise or large models. The SparkX i7 supports PLA, PETG, PLA-CF, and TPU filaments, enabling the printing of both decorative elements and more functional parts.CFS Lite Module – Multicolor PrintingThe Combo kit includes the CFS Lite module, which allows for the use of four filaments simultaneously. This makes it possible to print models in multiple colors without manually changing the material. The system supports automatic recognition of Creality filaments with RFID and an automatic filament refilling function, allowing for a seamless transition to the next spool when printing large models. The module also features its own filament feed motors and a tangling detection system. Manufacturer Creality Model SparkX i7 Combo Creality SparkX i7 Printing technology Fused Filament Fabrication (FFF) Build volume 260 × 260 × 255 mm Print speed up to 500 mm/s Acceleration up to 10,000 mm/s² Print accuracy 100 ± 0.1 mm Layer height 0.05 – 0.3 mm Filament diameter 1.75 mm Supported materials PLA, PETG, PLA-CF, TPU (64D or harder) Nozzle diameter 0.4 mm (compatible with 0.2 / 0.6 / 0.8 mm) Nozzle temperature up to 300°C Bed temperature up to 100°C Extruder Direct Drive Hotend quick tool-free replacement Build plate double-sided PEI sheet (gold texture) Leveling Fully automatic Camera AI 720p with lighting Error detection Spaghetti detection, air printing detection, filament run-out, filament tangle detection Resume printing after power loss Yes Connectivity USB Drive / Wi-Fi 2.4 GHz Communication port RS-485 (6-pin) Internal memory 8 GB EMMC File formats G-code / 3MF Software Creality Print 6.3 or newer System Creality OS Display 2.85" color touchscreen Status backlight RGB Interface Languages including English, German, Spanish,